IBM SAN192C-6 - Page 120

Xbar Ports Module-Type Model Status
--- ----- ---------------- ------------- --------------
1 0 Fabric Module 1 DS-X9710-FAB1 ok
2 0 Fabric Module 1 DS-X9710-FAB1 ok
3 0 Fabric Module 1 DS-X9710-FAB1 ok
4 0 Fabric Module 1 DS-X9710-FAB1 ok
5 0 Fabric Module 1 DS-X9710-FAB1 ok
6 0 Fabric Module 1 DS-X9710-FAB1 ok
Xbar Sw Hw
--- ----- ------
1 NA 1.0
2 NA 1.0
3 NA 1.0
4 NA 1.0
5 NA 1.0
6 NA 1.0
Xbar MAC-Address(es) Serial-Num
--- --------------- -----------------
1 NA JAE222305VS
2 NA JAE2217096X
3 NA JAE222305V5
4 NA JAE2217096L
5 NA JAE2217096J
6 NA JAE222305V8
2. Ensure that the required space is available in the bootflash: directory for the image files to be copied
using the dir bootflash: command. Use the delete bootflash: filename command to
remove any unnecessary files.
3. Copy the Supervisor-4 Module NX-OS kickstart and system images to the active supervisor module
bootflash, using an FTP, TFTP, SCP, SFTP, or a USB flash drive.
The Supervisor-4 images contain the string sf4 to identify them. Do not rename the images, use the
standard image names.
switch# copy
tftp://tftpserver.cisco.com/MDS/m9700-sf4ek9-kickstart-mz.8.4.1.bin
bootflash:m9700-sf4ek9-kickstart-mz.8.4.1.bin
switch# copy tftp://tftpserver.cisco.com/MDS/m9700-sf4ek9-mz.8.4.1.bin
bootflash:m9700-sf4ek9-mz.8.4.1.bin
4. Initiate the migration process of the active Supervisor-1 Module, using the migrate sup
kickstart <supervisor4-kickstart-image> system <supervisor4-system-image>
command in global config mode.
Note: The migrate sup kickstart <supervisor4-kickstart-image> system <supervisor4-
system-image> command is supported on NX-OS Release 8.4(1) or later. Invalid command
message is displayed, if this command is executed on other versions of NX-OS release.
Note: This command will verify if the images are compatible with the current system and the
kickstart images. If the images are not compatible, the following error message is displayed:
ERROR !! Version of kickstart image provided (8.x.x) does not
match running version.
switch# configure terminal
switch(config)# migrate sup kickstart m9700-sf4ek9-kickstart-mz.8.4.1.bin
system m9700-sf4ek9-mz.8.4.1.bin
Kickstart image file is /bootflash/m9700-sf4ek9-kickstart-mz.8.4.1.bin
System image file is /bootflash/m9700-sf4ek9-kickstart-mz.8.4.1.bin
5. During the migration, enter y when prompted.
Note: After this point, the migration process will be locked and you cannot cancel the migration
process. The migrate sup kickstart <supervisor4-kickstart-image> system
<supervisor4-system-image> command will then check if it has to initiate a single supervisor or
94IBM Storage Networking SAN192C-6, SAN384C-6 and SAN768C-6: SAN192C-6, SAN384C-6 and
SAN768C-6 Installation, Service, and User Guide