Icom IC-7300 HF Plus - Tone Control and Bandwidth Settings

12
SET MODE
12-3
Tone Control/TBW
SSB RX HPF/LPF (Default: – – – – – – – – –)
Sets the receive audio high-pass lter and low-pass
lter cutoff frequencies in 100 Hz steps.
Selectable ranges:
• HPF: 100 ~ 2000 Hz
• LPF: 500 ~ 2400 Hz
L If this item is set, the “SSB RX Bass” and “SSB RX
Treble” items are automatically set to “0.”
SSB RX Bass (Default: 0)
SSB RX Treble (Default: 0)
Sets the bass or treble level of the receive audio.
• Range: –5 ~ +5
AM RX HPF/LPF (Default: – – – – – – – – –)
Sets the receive audio high-pass lter or low-pass
lter cutoff frequencies in 100 Hz steps.
Selectable ranges:
• HPF: 100 ~ 2000 Hz
• LPF: 500 ~ 2400 Hz
L If this item is set, the “AM RX Bass” and “AM RX
Treble” items are automatically set to “0.”
AM RX Bass (Default: 0)
AM RX Treble (Default: 0)
Sets the bass or treble level of the receive audio.
• Range: –5 ~ +5
FM RX HPF/LPF (Default: – – – – – – – – –)
Sets the receive audio high-pass lter or low-pass
lter cutoff frequencies in 100 Hz steps.
Selectable ranges:
• HPF: 100 ~ 2000 Hz
• LPF: 500 ~ 2400 Hz
L If this item is set, the “FM RX Bass” and “FM RX
Treble” items are automatically set to “0.”
FM RX Bass (Default: 0)
FM RX Treble (Default: 0)
Sets the bass or treble level of the receive audio.
• Range: –5 ~ +5
CW RX HPF/LPF (Default: – – – – – – – – –)
RTTY RX HPF/LPF (Default: – – – – – – – – –)
Sets the receive audio high-pass lter or low-pass
lter cutoff frequencies in 100 Hz steps.
Selectable ranges:
• HPF: 100 ~ 2000 Hz
• LPF: 500 ~ 2400 Hz
SSB TX Bass (Default: 0)
SSB TX Treble (Default: 0)
Sets the bass or treble level of the receive audio.
• Range: –5 ~ +5
SSB TBW (WIDE) (Default: 100 – 2900)
SSB TBW (MID) (Default: 300 – 2700)
SSB TBW (NAR) (Default: 500 – 2500)
Sets the transmission passband width of wide, mid,
or narrow, by changing the lower and higher cutoff
frequencies.
• Lower frequency: 100, 200, 300 and 500 Hz
• Higher frequency: 2500, 2700, 2800 and 2900 Hz
SSB-D TBW (Default: 300 – 2700)
Sets the transmission passband width for the SSB-D
mode by changing the lower and higher cut-off
frequencies.
• Lower frequency: 100, 200, 300 and 500 Hz
• Higher frequency: 2500, 2700, 2800 and 2900 Hz
AM TX Bass (Default: 0)
AM TX Treble (Default: 0)
Sets the bass or treble level of the transmit audio .
• Range: –5 ~ +5
FM TX Bass (Default: 0)
FM TX Treble (Default: 0)
Sets the bass or treble level of the transmit audio .
• Range: –5 ~ +5
MENU
» SET > Tone Control/TBW
Previous view