Icom IC-7851

18-3
D Command table
18
CONTROL COMMAND
Cmd. Sub Cmd. Data Description
00 see p. 18-10 Send frequency data (transceive)
01 see p. 18-10 Send mode data (transceive)
02 see p. 18-10 Read band edge frequencies
03 see p. 18-10 Read operating frequency
04 see p. 18-10 Read operating mode
05 see p. 18-10 Set operating frequency
06 see p. 18-10 Operating mode selection for transceive
07 Select VFO mode
B0 Exchange the Main and Sub bands
B1 Equalize the Main and Sub bands
C2 00 or 01 Send/read the dualwatch setting
(00=OFF, 01=ON)
* Sub commands, C0 (dualwatch ON) and C1
(dualwatch OFF), are also usable for only
setting.
D2 00 Send/read Main band selection
* Sub command, D0, is also usable for only
setting.
01 Send/read Sub band selection
* Sub command, D1, is also usable for only
setting.
08 Select memory mode
0001 to
0099
Select memory channel
(0001=M-CH01, 0099=M-CH99)
0100 Select program scan edge channel P1
0101 Select program scan edge channel P2
09 Memory write
0A Memory to VFO
0B Memory clear
0E 00 Scan stop
01 Programmed/memory scan start
02 Programmed scan start
03 ∂F scan start
12 Fine programmed scan start
13 Fine ∂F scan start
22 Memory scan start
23 Select memory scan start
A1 Select ∂F scan span ±5 kHz
A2 Select ∂F scan span ±10 kHz
A3 Select ∂F scan span ±20 kHz
A4 Select ∂F scan span ±50 kHz
A5 Select ∂F scan span ±100 kHz
A6 Select ∂F scan span ±500 kHz
A7 Select ∂F scan span ±1 MHz
B0 Set as non-select channel
B1 Set as select channel
( The previously set number by CI-V is set
after turning power ON, or “1” is selected if
no selection is performed.)
01
Set as select channel “1”
02
Set as select channel “2”
03
Set as select channel “3”
B2 00 Set “ALL” for select memory scan
01
Set “1” for select memory scan
02
Set “2” for select memory scan
03
Set “3” for select memory scan
D0 Set scan resume OFF
D3 Set scan resume ON
0F 00 or 01 Read split setting (00=OFF, 01=ON)
00 Turn the split function OFF
01 Turn the split function ON
10 00 Send/read tuning step OFF
01 Send/read 100 Hz tuning step
02 Send/read 1 kHz tuning step
03 Send/read 5 kHz tuning step
04 Send/read 9 kHz tuning step
05 Send/read 10 kHz tuning step
06 Send/read 12.5 kHz tuning step
07 Send/read 20 kHz tuning step
08 Send/read 25 kHz tuning step
Cmd. Sub Cmd. Data Description
11 00 Send/read attenuator OFF
03 Send/read 3 dB attenuator
06 Send/read 6 dB attenuator
09 Send/read 9 dB attenuator
12 Send/read 12 dB attenuator
15 Send/read 15 dB attenuator
18 Send/read 18 dB attenuator
21 Send/read 21 dB attenuator
12* 00 00 or 01 Select/read ANT1 selection
(00=RX ANT OFF; 01=RX ANT ON)
01 00 or 01 Select/read ANT2 selection
(00=RX ANT OFF; 01=RX ANT ON)
02 00 or 01 Select/read ANT3 selection
(00=RX ANT OFF; 01=RX ANT ON)
03 00 Select/read ANT4 selection
(00=RX ANT OFF; fix)
13 00 Announce all data with voice synthesizer
01 Announce frequency and S-meter level with
voice synthesizer
02 Announce receive mode with voice
synthesizer
14* 01 0000 to
0255
Send/read [AF] level
(0000=max. CCW, 0255=max. CW)
02 0000 to
0255
Send/read [RF] level
(0000=max. CCW, 0255=max. CW)
03 0000 to
0255
Send/read [SQL] level
(0000=max. CCW, 0255=max. CW)
05 0000 to
0255
Send/read [APF] level
(0000=Pitch–550 Hz, 0128=Pitch,
0255=Pitch+550 Hz; 10 Hz steps)
06 0000 to
0255
Send/read [NR] level
(0000=0%, 0255=100%)
07 0000 to
0255
Send/read inner [TWIN PBT] position
( 0000=max. CCW, 0128=center,
0255=max. CW)
08 0000 to
0255
Send/read outer [TWIN PBT] position
( 0000=max. CCW, 0128=center,
0255=max. CW)
09 0000 to
0255
Send/read CW pitch
( 0000=300 Hz, 0128=600 Hz, 0255=900 Hz;
5 Hz steps)
0A 0000 to
0255
Send/read [RF PWR] position
(0000=max. CCW, 0255=max. CW)
0B 0000 to
0255
Send/read [MIC] position
(0000=max. CCW, 0255=max. CW)
0C 0000 to
0255
Send/read [KEY SPEED] level
(0000=6 wpm, 0255=48 wpm)
0D 0000 to
0255
Send/read [NOTCH] position
( 0000=max. CCW, 0128=center,
0255=max. CW)
0E 0000 to
0255
Send/read COMP level (0000=0, 0255=10)
0F 0000 to
0255
Send/read [DELAY] position
(0000=2.0d, 0255=13.0d)
11 0000 to
0255
Send/read [AGC] level
(0000=max. CCW to 0255=max. CW)
12 0000 to
0255
Send/read NB level
(0000=0%, 0255=100%)
13 0000 to
0255
Send/read [DIGI-SEL] position
(0000=max. CCW to 0255=max. CW)
14 0000 to
0255
Send/read DRIVE gain
(0000=0%, 0255=100%)
15 0000 to
0255
Send/read Monitor gain
(0000=0%, 0255=100%)
16 0000 to
0255
Send/read VOX gain
(0000=0%, 0255=100%)
17 0000 to
0255
Send/read Anti VOX gain
(0000=0%, 0255=100%)
18 0000 to
0255
Send/read [CONTRAST] position
(0000=max. CCW to 0255=max. CW)
19 0000 to
0255
Send/read BRIGHT level
(0000=0%, 0255=100%)