What to do if the Error LED is turned on (solid light) on Intermec EasyCoder PD42 Printer?
If the Intermec Printer's Error LED is on with a solid light, it indicates a problem. Check the following: * Ensure the printer has media or ribbon. * Verify the printhead is closed and locked. * Check for jammed or tangled media. * Make sure the label gap sensor isn't blocked. * Inspect the cutter, if there is one.
What to do if my Intermec EasyCoder PD42 Printer is upgrading its firmware?
If the printer is upgrading its firmware, wait for it to complete the task.
Why is my Intermec EasyCoder PD42 Printer working but not printing anything?
If the printer is working but nothing is printed, check that the printhead is correctly connected to the print mechanism.
What to do if Intermec Printer shows IP link error?
If your Intermec Printer shows 'IP link error', check if the network cable has been unplugged.
Why does my Intermec Printer skip labels when printing?
If labels are skipped when printing: * Run a new testfeed. * Check if the label gap sensor is disturbed by dust or foreign particles.
Why can't my Intermec EasyCoder PD42 feed labels or why is abnormal cutting happening?
If the label cannot feed or abnormal cutting occurs when using the cutter: * Check that the cutter is installed properly. * Check if the paper feed rods are sticky and clean if needed.
What to do if my Intermec EasyCoder PD42 Printer is out of media?
If your Intermec Printer is out of media, load media into the printer.
What to do if Intermec EasyCoder PD42 Printer is out of media?
To address an 'Out of media' error on your Intermec printer, load media into the printer. See the EasyCoder PD42 User’s Guide (P/N 934-009-xxx) for detailed instructions.
Why Intermec EasyCoder PD42 has no printing due to software error?
If the Intermec Printer is experiencing no printing due to a software error, check if a bad command was sent to the printer via Fingerprint or direct protocol. Also, check the Fingerprint application or the last issued instruction in Direct Protocol.
Why Intermec EasyCoder PD42 Printer is working, but nothing is printing?
If your Intermec Printer is not printing anything, there could be several reasons: * Ensure the direct thermal media is loaded correctly with the heat-sensitive side facing up. * Check that the ink-coated side of the thermal transfer ribbon faces the media. * Verify the printer settings for media type, paper type, and print method are correct. * Confirm the printhead is properly inserted into the print mechanism. * Inspect the cables from the print mechanism to the main board for damage and proper connection. * Consider replacing the printhead. * Check the label taken sensor is folded out and enabled and if there is a label left in the feed slot or the ambient light disturbs the label taken sensor.
Introduces the printer's capabilities and suitability for medium-duty applications.
Describes the exterior, connectors, and media compartment of the printer.
Explains the function of the print button and the meaning of the LED indicators.
Details how to interact with the printer's display and soft keys for operation.
Explains various connection methods for the printer to a computer system.
Provides instructions for loading different types of media into the printer.
Step-by-step guide on how to load a thermal transfer ribbon.
Explains the various operational states the printer can enter.
Covers methods for modifying the printer's setup parameters.
Details how to use test modes for verification and troubleshooting.
Lists common issues affecting printer operation and provides solutions.
Addresses common issues related to the quality of printed output.
Guides on diagnosing and resolving communication issues with the printer.
Procedures for making adjustments to improve printer performance.
Provides detailed technical specifications for the printer.
Describes the standard and optional communication interfaces for the printer.
Lists optional hardware kits that add functionality to the printer.
Details the dimensions and specifications for media rolls.
Explains different paper types and their dimensions.
Details parameters for serial communication setup.
Covers parameters for configuring media characteristics.
Controls transfer ribbon mechanism and ribbon sensor.
Details parameters for serial communication setup.
Covers parameters for configuring media characteristics.
Details various configuration options like emulation and print speed.
General| Media Type | Labels, Tags, Wristbands |
|---|---|
| Print Technology | Thermal Transfer, Direct Thermal |
| Print Resolution | 203 dpi |
| Maximum Print Width | 104 mm (4.09 in) |
| Media Thickness | 0.003 in to 0.010 in (0.08 mm to 0.25 mm) |
| Connectivity | USB, Serial, Ethernet |
| Power Requirements | 100-240 VAC, 50-60 Hz |
| Operating Temperature | +5°C to +40°C (+41°F to +104°F) |
| Storage Temperature | -40°F to 140°F (-40°C to 60°C) |
| Humidity | 10-90% RH non-condensing |
To Next Page