What to do if the label was not cut straight when using cutter on Intermec EasyCoder PD42?
If the label was not cut straight when using the cutter on your Intermec Printer, ensure that the media is loaded correctly.
What to do if the label was not cut successfully when using cutter on Intermec Printer?
If the label was not cut successfully when using the cutter on your Intermec Printer, verify the following: * Ensure the media is loaded correctly. * Confirm that the media thickness does not exceed 250 ?m (9.8 mils).
What to do if the label could not feed or abnormal cutting occurs when using cutter on Intermec EasyCoder PD42?
If the label could not feed or abnormal cutting occurs when using the cutter on your Intermec Printer, check the following: * Ensure the cutter is installed properly. * Check if paper feed rods are sticky. Clean if necessary using isopropyl alcohol.
What to do if there is abnormal function when using Label Taken Sensor on Intermec EasyCoder PD42 Printer?
If you experience abnormal function when using the Label Taken Sensor (LTS) on your Intermec Printer, check the following: * Verify if the LTS sensor is working. * Ensure media is loaded properly.
How to fix Intermec EasyCoder PD42 Printer showing LSS too high or LSS too low error?
To resolve the 'LSS too high, LSS too low' error on your Intermec printer, load the printer with media, restart the printer in Test mode and select the appropriate media type. For more information, see the EasyCoder PD42 User’s Guide (P/N 934-009-xxx). These errors can occur when you run a testfeed without any media installed, or if you have incorrect media settings.
What to do if Intermec EasyCoder PD42 shows Label not found error?
If your Intermec printer cannot find a label gap or black mark, go into Setup mode and verify that the label length parameter is correct. Also, verify that the Media type settings are correct.
What to do if Intermec EasyCoder PD42 displays Test Cutter not found?
If your Intermec Printer displays 'Test Cutter not found', ensure the cutter is installed properly. A cut-command has been sent but the printer cannot find the cutter.
What to do if Intermec EasyCoder PD42 Printer's cutter is not responding?
If your Intermec Printer displays 'Cutter not responding', ensure that the cutter is installed properly.
Introduces the printer's capabilities and suitability for medium-duty applications.
Describes the exterior, connectors, and media compartment of the printer.
Explains the function of the print button and the meaning of the LED indicators.
Details how to interact with the printer's display and soft keys for operation.
Explains various connection methods for the printer to a computer system.
Provides instructions for loading different types of media into the printer.
Step-by-step guide on how to load a thermal transfer ribbon.
Explains the various operational states the printer can enter.
Covers methods for modifying the printer's setup parameters.
Details how to use test modes for verification and troubleshooting.
Lists common issues affecting printer operation and provides solutions.
Addresses common issues related to the quality of printed output.
Guides on diagnosing and resolving communication issues with the printer.
Procedures for making adjustments to improve printer performance.
Provides detailed technical specifications for the printer.
Describes the standard and optional communication interfaces for the printer.
Lists optional hardware kits that add functionality to the printer.
Details the dimensions and specifications for media rolls.
Explains different paper types and their dimensions.
Details parameters for serial communication setup.
Covers parameters for configuring media characteristics.
Controls transfer ribbon mechanism and ribbon sensor.
Details parameters for serial communication setup.
Covers parameters for configuring media characteristics.
Details various configuration options like emulation and print speed.
General| Media Type | Labels, Tags, Wristbands |
|---|---|
| Print Technology | Thermal Transfer, Direct Thermal |
| Print Resolution | 203 dpi |
| Maximum Print Width | 104 mm (4.09 in) |
| Media Thickness | 0.003 in to 0.010 in (0.08 mm to 0.25 mm) |
| Connectivity | USB, Serial, Ethernet |
| Power Requirements | 100-240 VAC, 50-60 Hz |
| Operating Temperature | +5°C to +40°C (+41°F to +104°F) |
| Storage Temperature | -40°F to 140°F (-40°C to 60°C) |
| Humidity | 10-90% RH non-condensing |
To Next Page