EasyManuals Logo

Juniper SRX100 Hardware Guide

Juniper SRX100
154 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #102 background imageLoading...
Page #102 background image
Using the Reset Config Button on the SRX100 Services Gateway on page 85
Changing the Reset Config Button Behavior on the SRX100 Services Gateway on
page 86
Juniper Networks Technical Assistance Center on page 87
Monitoring the SRX100 Services Gateway Power System
The LEDs on the services gateway enable you to determine the performance and
operation. The Power LED, located on the front panel of the services gateway,
indicates the different settings with respect to the power system.
Table 31 on page 84 describes different Power LED status settings and their corrective
actions.
Table 31: Services Gateway Power LED Status
Possible Cause and Corrective ActionMeaningLED Status
Normal indication. No action is required.Device is receiving power, and the
internal power supply is functional.
Green
Normal indication. No action is required.Indicates that the power button has
been pressed and quickly released.
Amber
Verify that the AC power cord from the power
source to the device is not damaged. If the
insulation is cracked or broken, immediately
replace the cord or cable.
Ensure that the socket you plug in is in
working condition.
Ensure the device has an AC input voltage
between 100 and 240 VAC.
If you cannot determine the cause of the
problem or need additional assistance, see
Juniper Networks Technical Assistance
Center on page 87.
Indicates that the device is not
receiving power.
Off
Related Topics Monitoring the SRX100 Services Gateway Chassis Using the CLI on page 79
Monitoring the SRX100 Services Gateway Components Using LEDs on page 81
Monitoring the SRX100 Services Gateway Using Chassis Alarm Conditions on
page 83
Using the Reset Config Button on the SRX100 Services Gateway on page 85
Changing the Reset Config Button Behavior on the SRX100 Services Gateway on
page 86
Juniper Networks Technical Assistance Center on page 87
84 Monitoring the SRX100 Services Gateway Power System
SRX100 Services Gateway Hardware Guide

Table of Contents

Other manuals for Juniper SRX100

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Juniper SRX100 and is the answer not in the manual?

Juniper SRX100 Specifications

General IconGeneral
Routing protocolsBGP, IS-IS, MPLS, OSPF
Switching protocolsVLAN 802.1Q, 802.3ad/LACP, STP
Supported network protocolsIPv4, IPv6, CLNS
Firewall securityYes
Security algorithms3DES, DES
Authentication methodRADIUS, RSA SecureID, LDAP
VPN supportIPsec VPN
Data transfer rate0.1 Gbit/s
Input voltage100 - 240 V
Input frequency50/60 Hz
Heat dissipation35 BTU/h
Power requirements100-240, 50/60
Power over Ethernet (PoE)No
Power consumption (typical)30 W
SafetyUL 60950-1, CSA 60950-1, AS / NZS 60950-1, AS / NZS 60950-1, CB Scheme, EN 60950-1
CertificationFCC Class B ICES class B AS / NZS CISPR22 Class B AS / NZS CISPR22 Class B VCCI Class B EN 55022 Class B, EN 300386
Mounting typeRack mounting
Internal memory1024 MB
Storage temperature (T-T)-20 - 70 °C
Operating temperature (T-T)0 - 40 °C
Weight and Dimensions IconWeight and Dimensions
Weight1100 g
Dimensions (WxDxH)216 x 147 x 36 mm

Related product manuals