EasyManuals Logo

Juniper SRX100 Hardware Guide

Juniper SRX100
154 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #111 background imageLoading...
Page #111 background image
Related Topics SRX100 Services Gateway General Safety Guidelines and Warnings on page 93
SRX100 Services Gateway Fire Safety Requirements on page 96
SRX100 Services Gateway Installation Safety Guidelines and Warnings on page
97
SRX100 Services Gateway Laser and LED Safety Guidelines and Warnings on
page 101
SRX100 Services Gateway Electrical Safety Guidelines and Warnings on page 109
SRX100 Services Gateway Maintenance and Operational Safety Guidelines and
Warnings on page 105
SRX100 Services Gateway General Safety Guidelines and Warnings
General Safety Guidelines and Warnings
The following guidelines help ensure your safety and protect the services gateway
from damage. The list of guidelines might not address all potentially hazardous
situations in your working environment, so be alert and exercise good judgment at
all times.
Perform only the procedures explicitly described in this guide. Make sure that
only authorized service personnel perform other system services.
Keep the area around the chassis clear and free from dust before, during, and
after installation.
Keep tools away from areas where people could trip on them.
Wear safety glasses if you are working under any conditions that could be
hazardous to your eyes.
Do not perform any actions that create a potential hazard to people or make the
equipment unsafe.
Never install or manipulate wiring during electrical storms.
Never install electrical jacks in wet locations unless the jacks are specifically
designed for wet environments.
Do not open or remove chassis covers or sheet metal parts unless instructions
are provided in this guide. Such an action could cause severe electrical shock.
Do not push or force any objects through any opening in the chassis frame. Such
an action could result in electrical shock or fire.
Avoid spilling liquid onto the services gateway chassis or onto any services
gateway component. Such an action could cause electrical shock or damage the
services gateway.
Avoid touching uninsulated electrical wires or terminals that have not been
disconnected from their power source. Such an action could cause electrical
shock.
Qualified Personnel Warning
SRX100 Services Gateway General Safety Guidelines and Warnings 93
Appendix A: Safety and Regulatory Compliance Information

Table of Contents

Other manuals for Juniper SRX100

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Juniper SRX100 and is the answer not in the manual?

Juniper SRX100 Specifications

General IconGeneral
Routing protocolsBGP, IS-IS, MPLS, OSPF
Switching protocolsVLAN 802.1Q, 802.3ad/LACP, STP
Supported network protocolsIPv4, IPv6, CLNS
Firewall securityYes
Security algorithms3DES, DES
Authentication methodRADIUS, RSA SecureID, LDAP
VPN supportIPsec VPN
Data transfer rate0.1 Gbit/s
Input voltage100 - 240 V
Input frequency50/60 Hz
Heat dissipation35 BTU/h
Power requirements100-240, 50/60
Power over Ethernet (PoE)No
Power consumption (typical)30 W
SafetyUL 60950-1, CSA 60950-1, AS / NZS 60950-1, AS / NZS 60950-1, CB Scheme, EN 60950-1
CertificationFCC Class B ICES class B AS / NZS CISPR22 Class B AS / NZS CISPR22 Class B VCCI Class B EN 55022 Class B, EN 300386
Mounting typeRack mounting
Internal memory1024 MB
Storage temperature (T-T)-20 - 70 °C
Operating temperature (T-T)0 - 40 °C
Weight and Dimensions IconWeight and Dimensions
Weight1100 g
Dimensions (WxDxH)216 x 147 x 36 mm

Related product manuals