Mindray BeneView T8 - C.15 RM Setup

To Next Page

To Previous Page

Factory Defaults

C-12

C.15 RM Setup

Factory default settings

RM Setup

Adult Pediatric Neonate

Alarm On

Alm Lev Med

Alm Rec Off

Apnea Time 20 s

TV / MV TV

Sensor Type Disposable

Ventilation Mode Spontaneous

Alarm Limits Setup

RR High 30 30 100

RR Low 8 8 30

PEEP High 10

PEEP Low 0

PIP High 40

PIP Low 1

MVe High 30.0 30.0 10.0

MVe Low 2.0 2.0 0.5

RM Waveform

Sweep 25 mm/s

Main Page

Default Chapter3
- Revision History3
- Contact Information6
- Intended Audience7
- Table of Contents9
1 Safety19
- Safety Information19
- Equipment Symbols22
- Reference Literature23
2 The Basics25
- Monitor Description25
- Main Unit26
- Satellite Module Rack31
- Modules32
  - Plug-In Modules32
  - Multi-Parameter Module33
- Display Screen34
- Quickkeys36
3 Basic Operations39
- Installation39
  - Unpacking and Checking40
  - Environmental Requirements41
- Getting Started42
  - Turning Power on42
  - Starting Monitoring42
- Disconnecting from Power43
- Using a Mice44
- Using Keyboards45
- Using the Touchscreen45
- Using the Main Menu46
- Using a CF Storage Card47
- Changing General Settings48
- Default Configurations51
4 Managing Patients53
- Admitting a Patient53
- Quick Admitting a Patient54
- Editing Patient Information55
- Discharging a Patient55
- Connecting to a Central Monitoring System56
5 User Screens57
- Tailoring Your Screens57
- Viewing Minitrends59
- Viewing Oxycrg61
- Viewing Other Patients62
  - Care Group62
  - Understanding the View Other Patient Window62
- Understanding the Big Numerics Screen64
6 Alarms65
- Alarm Categories65
- Alarm Levels66
- Alarm Indicators67
- Alarm Tone Configuration69
- Using Alarms70
- Pausing Alarms72
- Silencing the System72
- Latching Alarms72
- Clearing Technical Alarms73
- When an Alarm Occurs73
7 Monitoring Ecg/Resp75
- Introduction75
- Safety76
- Preparing to Monitor ECG77
- Understanding the ECG Display82
- Changing ECG Settings83
- About ST Monitoring87
- About Arrhythmia Monitoring89
- 12-Lead ECG Monitoring91
- Monitoring Respiration (Resp)94
8 Monitoring Spo97
- Introduction97
- Safety98
- Identifying Spo Modules99
- Applying the Sensor99
- Changing Spo Settings100
- Masimo Information104
- Nellcor Information104
9 Monitoring NIBP105
- Introduction105
- Safety106
- Measurement Limitations106
- Measurement Methods107
- Setting up the NIBP Measurement107
- Understanding the NIBP Numerics109
- Changing NIBP Settings110
- Assisting Venous Puncture111
- Resetting NIBP111
- NIBP Leakage Test111
- NIBP Accuracy Test112
- Calibrating NIBP113
10 Monitoring Temp115
- Introduction115
- Safety115
- Making a Temp Measurement116
- Understanding the Temp Display116
- Setting the Temperature Unit116
11 Monitoring IBP117
- Introduction117
- Safety117
- Setting up the Pressure Measurement118
- Understanding the IBP Display119
- Changing IBP Settings120
- Zeroing the Transducer121
- Making the Pressure Calibration122
12 Monitoring Cardiac Output125
- Introduction125
- Understanding the C.O. Display126
- Influencing Factors126
- Setting up the C.O. Measurement127
- Measuring the Blood Temperature130
- Changing C.O. Settings130
  - Setting the Temperature Unit130
  - Setting the Interval between Measurements130
13 Monitoring Carbon Dioxide131
- Introduction131
- Identifying CO Modules132
- Preparing to Measure CO133
- Zeroing the Sensor140
- Calibrating the Sensor141
14 Monitoring AG143
- Understanding the AG Display144
- Connecting AG Accessories145
- Changing AG Settings146
  - Changing the Operating Mode147
- Troubleshooting148
15 Monitoring ICG149
- Understanding ICG Parameters150
- Understanding the ICG Display151
- ICG Limitations152
  - Placing ICG Sensors153
- Changing ICG Settings154
16 Monitoring bis155
- Safety Information156
- Understanding the bis Display157
- Setting up the bis Measurement158
- Continuous Impedance Check159
- Cyclic Impedance Check160
- BIS Sensor Check Window161
- Choosing the bis Smoothing Rate162
17 Monitoring RM163
- Safety Information165
- Preparing to Monitor RM166
- Understanding the RM Display167
- Changing RM Settings168
  - Changing the Wave Scale169
- Understanding the Respiratory Loops170
- Zeroing the RM Module171
18 Freezing Waveforms173
- Unfreezing Waveforms174
19 Review175
- Reviewing Graphic Trends176
- Reviewing Tabular Trends178
- Reviewing NIBP Measurements180
- Reviewing Alarms181
- Reviewing Waveforms182
20 Calculations185
- Dose Calculations186
  - Selecting the Proper Drug Unit187
  - Titration Table188
- Oxygenation Calculations189
  - Entered Parameters190
- Ventilation Calculations191
  - Entered Parameters192
- Hemodynamic Calculations193
  - Entered Parameters194
  - Calculated Parameters195
- Renal Calculations196
  - Entered Parameters197
- Understanding the Review Window198
- Recording199
21 Recording200
- Overview of Recording Types200
- Starting and Stopping Recordings201
- Setting up the Recorder202
  - Switching Gridlines on or off203
- Loading Paper204
- Removing Paper Jam205
22 Other Functions207
- Nurse Call208
23 Batteries211
- Conditioning the Batteries212
- Checking the Batteries213
- Recycling the Batteries214
24 Care and Cleaning215
- Cleaning216
25 Maintenance217
- Service Tasks218
- Checking Monitor and Module Information219
- Calibrating CO 2220
- Calibrating AG221
- Setting up IP Address222
26 Accessories223
- ECG Accessories224
- NIBP Accessories227
- Temp Accessories228
- C.O. Accessories229
- AG Accessories231
- Others232
A Product Specifications233
- A.2 Physical Specifications236
- A.3 Hardware Specifications237
- A.4 Data Storage240
- A.5 Measurement Specifications241
C Factory Defaults261
- C.4 ECG Setup262
- C.5 Resp Setup263
- C.7 NIBP Setup265
- C.9 IBP Setup266
- C.10 C.O. Setup267
- C.12 AG Setup269
- C.13 ICG Setup270
- C.14 bis Setup271
- C.15 RM Setup272
D Alarm Messages273
- D.1 Physiological Alarm Messages274
- D.2 Technical Alarm Messages275
E Symbols and Abbreviations283
- E.2 Abbreviations285

Mindray BeneView T8 - C.15 RM Setup

Table of Contents

Other manuals for Mindray BeneView T8

Related product manuals