Mitsubishi Electric MELSEC iQ-F Series - Page 229

10 TROUBLESHOOTING
10.5 List of Error Codes
227
10
3160H The number of points of link devices of the device
stations set to "CC-Link IE TSN Class A" in "CC-
Link IE TSN Class" of "Network Configuration
Settings" under "Basic Settings" exceeds the
number of points that can be assigned.
In "Network Configuration Settings" under "Basic Settings", review
the device assignment settings so that the number of points of link
devices of the stations with detailed information 2 does not exceed
the number of points assigned to stations with CC-Link IE TSN Class
A.
Parameter
information
• Parameter type
• Intelligent module
No.
• Parameter No.
Target station
information
• Station No.
• IP address
31ABH Sending/receiving cyclic data within the "Low-
Speed" period to/from a device station with
"Communication Period Setting" set to "Low-
Speed" cannot be guaranteed.
• Set "Low-Speed" in "Multiple Period Setting" to a value that is
equal to or higher than the one displayed for 'Multiple period
setting (low speed)' (Un\G44594).
• Set "Communication Period Interval Setting" in "Basic Period
Setting" to a value that is equal to or higher than the one displayed
for 'Communication cycle interval (calculation value)' (Un\G44595).
Parameter
information
• Parameter type

31ACH The settings do not match between "CC-Link IE
TSN Class" of the device stations set in "Network
Configuration Settings" and "CC-Link IE TSN
Class Setting" under "Connection Device
Information" of "Basic Settings".
Set "CC-Link IE TSN Class" in "Network Configuration Settings" of
the device stations to "CC-Link IE TSN Class B". Alternatively, set
"CC-Link IE TSN Class Setting" under "Connection Device
Information" of "Basic Settings" to "Mixture of CC-Link IE TSN Class
B/A or CC-Link IE TSN Class A Only".
Parameter
information
• Parameter type

3600H Response data of the dedicated instruction
cannot be created.
• Increase the request interval.
• Decrease the number of request nodes.
• Wait for a response to the previous request before sending the
next request.
• Correct the timeout value.

3601H to
3603H
System error Please consult your local Mitsubishi representative. 
3607H to
360DH
System error Please consult your local Mitsubishi representative. 
3C00H A hardware failure has been detected. • Take measures to reduce noise.
• Reset the CPU module, and run it again. If the same error occurs
again even after taking the above, the possible cause is a
hardware failure of the module or extension cable. Please consult
your local Mitsubishi representative.

3C01H A hardware failure has been detected. • Take measures to reduce noise.
• Reset the CPU module, and run it again. If the same error occurs
again even after taking the above, the possible cause is a
hardware failure of the module or extension cable. Please consult
your local Mitsubishi representative.

3C02H A hardware failure has been detected. • Take measures to reduce noise.
• Reset the CPU module, and run it again. If the same error occurs
again even after taking the above, the possible cause is a
hardware failure of the module or extension cable. Please consult
your local Mitsubishi representative.

3C0FH A hardware failure has been detected. • Take measures to reduce noise.
• Reset the CPU module, and run it again. If the same error occurs
again even after taking the above, the possible cause is a
hardware failure of the module or extension cable. Please consult
your local Mitsubishi representative.

3C10H A hardware failure has been detected. • Take measures to reduce noise.
• Reset the CPU module, and run it again. If the same error occurs
again even after taking the above, the possible cause is a
hardware failure of the module or extension cable. Please consult
your local Mitsubishi representative.

3C13H A hardware failure has been detected. Reset the CPU module, and run it again. If the same error occurs
again even after doing so, the possible cause is a hardware failure of
the error module or CPU module. Please consult your local
Mitsubishi representative.

3C14H A hardware failure has been detected. Reset the CPU module, and run it again. If the same error occurs
again even after doing so, the possible cause is a hardware failure of
the error module or CPU module. Please consult your local
Mitsubishi representative.

Error
code
Error definition and causes Action Detailed
information 1
Detailed
information 2