NETGEAR Nighthawk D7000 User Manual

8. In the Enter Client's PIN field, enter the PIN number of the WiFi device.
9. Click the Next button.
For four minutes, the modem router attempts to find the WiFi device (that is, the client) that you want
to join the modem router’s main WiFi network.
During this time, the WiFi LED on the top panel of the modem router blinks white.
10. Within four minutes, go to the WiFi device and use its WPS software to join the network without entering
a password.
When the modem router establishes a WPS connection, the WiFi LED lights solid white and the Add
WPS Client page displays a confirmation message.
11. To verify that the WiFi device is connected to the modem router’s main WiFi network, select BASIC
> Attached Device.
The WiFi device displays onscreen.
Manage the Basic WiFi Settings and WiFi Security of the Guest
Network
A guest network allows visitors to use the Internet without using your WiFi security key. By default, the
guest WiFi network is disabled.You can enable and configure the guest WiFi network for each WiFi band.
The modem router simultaneously supports the 2.4 GHz band for 802.11n, 802.11g, and 802.11b devices
and the 5 GHz band for 802.11ac, 802.11na, and 802.11a devices.
The WiFi mode of the guest WiFi network depends on the WiFi mode of the main WiFi network. For
example, if you configure the WiFi mode for the main WiFi network as Up to 54 Mbps in the 2.4 GHz band,
the guest WiFi network also functions in the Up to 54 Mbps mode in the 2.4 GHz band. For information
about configuring the WiFi mode, see View or Change the Basic WiFi Settings on page 102.
The modem router provides two default guest networks with the following names (SSIDs):
• 2.4 GHz band. NETGEAR_Guest1
• 5 GHz band. NETGEAR-5G_Guest1
By default, these networks are configured as open networks without security but are disabled.You can
enable one or both networks.You can also change the SSIDs for these networks.
Manage the WiFi Network Settings
117
Nighthawk AC1900 WiFi VDSL/ADSL Modem Router Model D7000

NETGEAR Nighthawk D7000 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.3, IEEE 802.3ab, IEEE 802.3u
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet LAN interface type	Gigabit Ethernet
Wi-Fi band	Dual-band (2.4 GHz / 5 GHz)
Wi-Fi standards	802.11a, Wi-Fi 5 (802.11ac), 802.11b, 802.11g, Wi-Fi 4 (802.11n)
Top Wi-Fi standard	Wi-Fi 5 (802.11ac)
WLAN data transfer rate (max)	1300 Mbit/s
USB version	3.2 Gen 1 (3.1 Gen 1)
Rack mounting	No
Bandwidth (first)	2.4 GHz
Bandwidth (second)	5 GHz
USB ports quantity	2
WLAN data transfer rates supported	600, 1300 Mbit/s
Memory card slot(s)	-
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Ethernet LAN (RJ-45) ports	5
DSL specification	VDSL, VDSL2, ADSL, ADSL2, ADSL2+
Antennas quantity	3
Security algorithms	WPA, WPA2-PSK, WPS
Product type	Tabletop router
Product color	Black
Flash memory	128 MB
Internal memory	256 MB
Processor frequency	1000 MHz
Cables included	LAN (RJ-45)
Power source type	AC

Weight and Dimensions

Depth	185 mm
Width	285 mm
Height	50 mm
Weight	750 g