EasyManuals Logo

NETGEAR Nighthawk D7000 User Manual

NETGEAR Nighthawk D7000
313 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #298 background imageLoading...
Page #298 background image
• Power LED Is Off on page 298
• Power LED Remains Solid Amber on page 298
• WiFi LED Is Off on page 298
• Troubleshoot the Internet Connection on page 299
Power LED Is Off
If the Power LED and other LEDs are off when your modem router is turned on, do the following:
• Make sure that the Power On/Off button on the back is in the on position, that is, it is pushed in.
• Make sure that the power cord is correctly connected to your modem router and that the power supply
adapter is correctly connected to a functioning power outlet.
• Make sure that you are using the 12 VDC 3.5A power adapter that NETGEAR supplied for this product.
If the error persists, a hardware problem might exist. For recovery instructions or help with a hardware
problem, contact technical support at www.netgear.com/support.
Power LED Remains Solid Amber
Two seconds after the power is first applied, the Power LED lights solid amber for about 10 seconds,
turns off for about 20 seconds, and then lights solid amber again. About two minutes after the power is
first applied, the Power LED lights solid white, indicating that the startup procedure is complete and the
modem router is ready.
If the Power LED remains solid amber and does not turn solid white, a failure occurred or the modem
router is malfunctioning.
If the Power LED does not turn solid white, do the following:
1. Turn the power off and back on and wait several minutes to see if the modem router recovers.
2. If the modem router does not recover, ptress and hold the Reset button to return the modem router
to its factory settings.
If the error persists, a hardware problem might exist. For recovery instructions or help with a hardware
problem, contact technical support at www.netgear.com/support.
WiFi LED Is Off
If the WiFi LED remains off, check to see if both radios on the modem router are disabled (see Control
the WiFi Radios on page 123). By default, both radios are enabled and the WiFi LED lights solid white.
You Cannot Log In to the Modem Router
If you are unable to log in to the modem router from a computer on your local network and use the web
management interface, check the following:
Diagnostics and Troubleshooting
298
Nighthawk AC1900 WiFi VDSL/ADSL Modem Router Model D7000

Table of Contents

Other manuals for NETGEAR Nighthawk D7000

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the NETGEAR Nighthawk D7000 and is the answer not in the manual?

NETGEAR Nighthawk D7000 Specifications

General IconGeneral
Ethernet LANYes
Cabling technology10/100/1000Base-T(X)
Networking standardsIEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.3, IEEE 802.3ab, IEEE 802.3u
Ethernet LAN data rates10, 100, 1000 Mbit/s
Ethernet LAN interface typeGigabit Ethernet
Wi-Fi bandDual-band (2.4 GHz / 5 GHz)
Wi-Fi standards802.11a, Wi-Fi 5 (802.11ac), 802.11b, 802.11g, Wi-Fi 4 (802.11n)
Top Wi-Fi standardWi-Fi 5 (802.11ac)
WLAN data transfer rate (max)1300 Mbit/s
USB version3.2 Gen 1 (3.1 Gen 1)
Rack mountingNo
Bandwidth (first)2.4 GHz
Bandwidth (second)5 GHz
USB ports quantity2
WLAN data transfer rates supported600, 1300 Mbit/s
Memory card slot(s)-
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Ethernet LAN (RJ-45) ports5
DSL specificationVDSL, VDSL2, ADSL, ADSL2, ADSL2+
Antennas quantity3
Security algorithmsWPA, WPA2-PSK, WPS
Product typeTabletop router
Product colorBlack
Flash memory128 MB
Internal memory256 MB
Processor frequency1000 MHz
Cables includedLAN (RJ-45)
Power source typeAC
Weight and Dimensions IconWeight and Dimensions
Depth185 mm
Width285 mm
Height50 mm
Weight750 g

Related product manuals