EasyManuals Logo

Newport XPS Programmer's Manual

Newport XPS
722 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #11 background imageLoading...
Page #11 background image
XPS Unified Programmer’s Manual
7.2.1.315
SpindleSlaveModeDisable ..................................................................... 461
7.2.1.316 SpindleSlaveModeEnable ...................................................................... 462
7.2.1.317 SpindleSlaveParametersGet ................................................................... 463
7.2.1.318 SpindleSlaveParametersSet .................................................................... 464
7.2.1.319 TCLScriptExecute .................................................................................. 466
7.2.1.320 TCLScriptExecuteAndWait ................................................................... 467
7.2.1.321 TCLScriptExecuteWithPriority .............................................................. 469
7.2.1.322 TCLScriptKill ........................................................................................ 471
7.2.1.323 TCLScriptKillAll ................................................................................... 472
7.2.1.324 TCLScriptRunningListGet ..................................................................... 473
7.2.1.325 TCP_CloseSocket .................................................................................. 474
7.2.1.326 TCP_ConnectToServer .......................................................................... 475
7.2.1.327 TCP_GetError ........................................................................................ 476
7.2.1.328 TCP_SetTimeout .................................................................................... 477
7.2.1.329 TimerGet ................................................................................................ 478
7.2.1.330 TimerSet ................................................................................................. 479
7.2.1.331 TZEncoderCouplingMatrixGet .............................................................. 480
7.2.1.332 TZEncoderCouplingMatrixSet ............................................................... 482
7.2.1.333 TZEncoderCouplingModeGet ................................................................ 484
7.2.1.334 TZEncoderCouplingModeSet ................................................................ 485
7.2.1.335 TZFocusModeDisable ............................................................................ 486
7.2.1.336 TZFocusModeEnable ............................................................................. 487
7.2.1.337 TZMappingModeGet ............................................................................. 488
7.2.1.338 TZMappingModeSet .............................................................................. 489
7.2.1.339 TZMotorDecouplingMatrixGet .............................................................. 490
7.2.1.340 TZMotorDecouplingMatrixSet .............................................................. 492
7.2.1.341 TZMotorDecouplingModeGet ............................................................... 494
7.2.1.342 TZMotorDecouplingModeSet ................................................................ 495
7.2.1.343 TZPTExecution ...................................................................................... 496
7.2.1.344 TZPTLoadToMemory ............................................................................ 498
7.2.1.345 TZPTParametersGet ............................................................................... 500
7.2.1.346 TZPTPulseOutputGet ............................................................................. 501
7.2.1.347 TZPTPulseOutputSet ............................................................................. 503
7.2.1.348 TZPTResetInMemory ............................................................................ 505
7.2.1.349 TZPTVerification ................................................................................... 506
7.2.1.350 TZPTVerificationResultGet ................................................................... 508
7.2.1.351 TZPVTExecution ................................................................................... 510
7.2.1.352 TZPVTLoadToMemory ......................................................................... 512
7.2.1.353 TZPVTParametersGet ............................................................................ 514
7.2.1.354 TZPVTPulseOutputGet .......................................................................... 515
7.2.1.355 TZPVTPulseOutputSet .......................................................................... 517
7.2.1.356 TZPVTResetInMemory ......................................................................... 519
7.2.1.357 TZPVTVerification ................................................................................ 520
7.2.1.358 TZPVTVerificationResultGet ................................................................ 522
7.2.1.359 TZTrackingCutOffFrequencyGet ........................................................... 524
7.2.1.360 TZTrackingCutOffFrequencySet ........................................................... 525
7.2.1.361 TZTrackingUserMaximumZZZTargetDifferenceGet ............................ 526
7.2.1.362 TZTrackingUserMaximumZZZTargetDifferenceSet ............................. 527
7.2.1.363 XYCrossTalkCompensationMotorDecouplingGet ................................ 528
7.2.1.364 XYCrossTalkCompensationMotorDecouplingSet ................................. 529
7.2.1.365 XYGroupPositionCorrectedProfilerGet ................................................. 530
xi EDH0373En1023 — 01/18

Table of Contents

Other manuals for Newport XPS

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Newport XPS and is the answer not in the manual?

Newport XPS Specifications

General IconGeneral
Controller TypeMulti-axis motion controller
Power Supply24 VDC
Communication InterfaceEthernet
Programming LanguageC, C++, .NET, LabVIEW
Supported Motor TypesStepper
Operating System CompatibilityWindows
AxesUp to 8 axes

Related product manuals