KENR6932 189
Index Section
Index
A
Accessory Drive - Remove and Install................. 101
Installation
Procedure ...................................... 102
Removal Procedure ......................................... 101
Air Compressor - Remove and Install.................. 183
Installation
Procedure ...................................... 185
Removal Procedure ......................................... 183
Alternator - Install (Alternators with Mounting
Lugs).................................................................. 181
Installation Procedure ...................................... 181
Alternator - Install (Alternators with Mounting
Pads) ................................................................. 182
Installation Procedure ...................................... 182
Alternator - Remove (Alternators with Mounting
Lugs).................................................................. 180
Removal Procedure ......................................... 180
Alternator - Remove (Alternators with Mounting
Pads) ................................................................. 181
Removal Procedure ......................................... 181
Alternator Belt - Remove and Install.................... 173
Installation P
rocedure ...................................... 174
Removal Procedure ......................................... 173
B
Bearing Cleara
nce - Check ................................. 164
Measurement Procedure ................................. 164
Boost Pressure Sensor - Remove and Install...... 170
Installation Pr
ocedure ...................................... 171
Removal Procedure ......................................... 170
C
Camshaft - Remo
ve and Install ........................... 129
Installation Procedure ...................................... 129
Removal Procedure ......................................... 129
Camshaft Bearin
gs - Remove and Install ............ 133
Installation Procedure ...................................... 134
Removal Procedure ......................................... 133
Camshaft Gear - Re
move and Install .................. 130
Installation Procedure ...................................... 132
Removal Procedure ......................................... 130
Connecting Rod Be
arings - Install (Connecting rods
in position) ......................................................... 153
Installation Procedure ...................................... 153
Connecting Rod Be
arings - Remove (Connecting
rods in position) ................................................. 152
Removal Procedure ......................................... 152
Coolant Temperat
ure Sensor - Remove and
Install ............................................................. .... 167
Installation Procedure ...................................... 167
Removal Procedur
e ......................................... 167
Crankcase Breather - Install (Filtered Breather).. 108
Installation Procedure ...................................... 108
Crankcase Breathe
r-Install(Unfiltered
Breather)............................................................ 106
Installation Procedure ...................................... 106
Crankcase Bre
ather - Remove (Filtered
Breather)............................................................ 105
Removal Procedure ......................................... 105
Crankcase Bre
ather - Remove (Unfiltered
Breather)............................................................ 103
Removal Procedure ......................................... 103
Crankshaft - I
nstall............................................... 159
Installation Procedure ...................................... 159
Crankshaft - Remove........................................... 157
Removal Proced
ure ......................................... 157
Crankshaft Front Seal - Remove and Install.......... 87
Installation Procedure ........................................ 87
Removal Proced
ure ........................................... 8 7
Crankshaft Gear - Remove and Install ................ 163
Installation Procedure ...................................... 163
Removal Procedu
re ......................................... 16 3
Crankshaft Main Bearings - Remove and Install
(Crankshaft in position)...................................... 154
Installation P
rocedure ...................................... 156
Removal Procedure ......................................... 154
Crankshaft Position Sensor - Remove and
Install ................................................................. 165
Installation Procedure ...................................... 165
Removal Procedure ......................................... 165
Crankshaft Rear
Seal - Install................................ 75
InstallationProcedureWithOilPaninPosition.. 75
Installation Procedure Without Isolating Frame for
the Oil Pan ....................................................... 77
Crankshaft Rear Seal - Remove............................ 75
Removal Procedure ........................................... 75
Crankshaft Timin
g Ring - Remove and Install ..... 161
Installation Procedure ...................................... 162
Removal Procedure ......................................... 161
Cylinder Head - In
stall ......................................... 124
Installation Procedure ...................................... 124
Cylinder Head - Remove ..................................... 121
Removal Procedure
......................................... 121
D
Disassembly and Assembly Section........................ 5
E
ECM Mounting Bracket - Remove and Install...... 178
Installation Procedure ...................................... 179
Removal Procedur
e ......................................... 178
Electric Starting Motor - Remove and Install ....... 182
Installation Procedure ...................................... 183
Removal Procedure
......................................... 182
Electronic Control Module - Remove and Install.. 176
Installation Procedure ...................................... 177
Removal Procedure
......................................... 176
Electronic Unit Injector - Install .............................. 30
Alternative Installation Procedure ...................... 32
Installation Proce
dure ........................................ 30