Polyend Tracker Mini - 12.5 Configuring Effects

271
Polyend Tracker Mini Manual
270
Polyend Tracker Mini Manual
Performance Mode
12
Performance Mode
12
▌ SETTING A TRACK PATTERN
1. Playback stopped.
2. Press [Menu] and open the ‘Perform’ Page for Performance Mode.
3. Hold [Track 1] to [Track 8] Screen button + Press (Up) or (Down). This
selects the pattern assigned to the chosen track. These can also be
changed during playback as a real-time performance and remix
technique.
▌ CHANGING PERFORM TEMPLATE SAVE BEHAVIOUR
1. Hold [Shift] + [4] or use [Menu] to select the ‘Cong’ Menu.
2. Ensure the left window is highlighted red i.e. in focus. Navigate windows
by pressing (Left) or (Right). Menu windows will automatically be
selected when pressing the relevant screen keys below the window to
navigate (Up) or (Down).
3. Press (Up) (Down) highlight with the bounding box over the ‘Project
Settings’ option. Alternatively press the relevant screen keys below the
left window to navigate (Up) or (Down).
4. Press (Up) (Down) to highlight with the bounding box over the
‘Performance presets’ option in the central window. Alternatively press
the relevant screen keys below the central window to navigate (Up) or
(Down).
5. To change the selected parameter / setting, Press [Change]. The
parameter pop-up window listing the available options will appear.
6. Press (Up) / (Down) or (Up) / (Down) Screen buttons to highlight the
desired option. The ‘Global’ setting will save the perform template for all
projects while ‘Per Project’ will save on an individual project basis.
Global is default.
7. Press [Apply] - 6
th
Screen button to conrm selection or [Cancel] - 3
rd
Screen button to exit without changing.
NOTESNOTES
12.5 Conguring Effects
Effects can be setup in record mode with up to 12 effects being congured
from a library of 21 performance effects. By default the performance preset
is saved on a global basis, but can be changed to be saved ‘per-project’ in
the ‘Cong’ settings.
▌ CREATING AN EFFECT TEMPLATE
1. Press [Menu] and open the ‘Perform’ Page for Performance Mode.
2. Press [Rec] to select record mode. Values and bounding box are red.
3. Navigate between effect slots, Press (Left) or (Right).
4. To cycle the effect selected for the chosen column slot, Press (Up) or
(Down) while in Rec mode. A total of 21 effect options available.
5. To swap effects, Hold [Shift] + (Right) or (Left). This will swap the
currently selected effect along with the values with the slot chosen. This
can be used as a creative option.
6. Hold [+] / [-] for one of the 4 slot rows to edit then Press (Up) or (Down)
incrementally change the value of the selected effect row. Press [+] / [-]
+ Hold (Up) (Down) to continuously increase or decrease. Top row 1 is
reserved to reset the default value and cannot be permanently changed
for many effects.
7. Repeat steps 3 - 5 for other effect slots. 12 slots are available.
8. Press [Rec] to turn record mode off.
Swap Effects
Hold [Shift] + (Right) / (Left)
Select Slot
Press (Right) / (Left)
Pad Row 1
MIDI CC Row
Pad Row 2
Pad Row 3
Pad Row 4
Change Effects
Press (Up) / (Down)
Track 1
Patt: 1
---
---
-100
+100
-50
---
---
-1
-1
-1
---
---
-5
+5
-7
---
---
-1
-1
-1
---
---
-1
-1
-1
---
---
-1
-1
-1
---
---
-1
-1
-1
---
---
-1
-1
-1
---
---
-1
-1
-1
---
---
-1
-1
-1
>>>
>>>
/16
/16
/16
---
---
-1
-1
-1
Track 2
Patt: 1
Track 3
Patt: 1
Track 4
Patt: 1
Track 6
Patt: 1
Track 5
Patt: 1
Track 7
Patt: 1
Track 8
Patt: 1
Performance FX
Volume High-pass cutoff Sample end Tune Delay send Sample Playback Panning Band-pass cutoff Low-pass cutoff Sample position Reverb send Volume LFO
0m:00s P1.028
Rec