Reely HT-6 - Page 52

To Next Page

To Previous Page

• Alternatinglydeectthecontroleverforthepitchfunctiontothestopandpushthebuttons„UP“or„DOWN“toset

the path of the swash plate up and down. If the button „OK“ is pushed and held, the factory parameters are called.

If a negative value is entered, the movement direction of the swash plate will change.

• Keepthebutton„CANCEL“pushedforalongerperiodtosavethesettings.Thedisplaythenshowsthefunction

setup menu again.

• Pushthebutton„CANCEL“repeatedlyuntilyougetbacktotheoperatingdisplay.

Important:

Adjust the swash plate paths so that even min. and max. pitch will still provide the maximum nod and roll

path without the swash plate linkage topping mechanically or being limited.

Main Page

Default Chapter2
- Table of Contents2
1 Introduction4
2 Explanation of Symbols4
3 Intended Use5
4 Product Description5
5 Scope of Delivery6
6 Safety Information6
- A) General Information6
- B) Operation7
7 Notes on Batteries and Rechargeable Batteries8
8 Charging Rechargeable Batteries8
9 Transmitter Controls9
10 Setting up the Transmitter10
- A) Inserting the Batteries10
- B) Switching on the Transmitter11
- C) Modifying the Throttle Function13
- D) Setting the Control Stick Length14
11 Setting up the Receiver15
- A) Connecting the Receiver15
- B) LED Display16
- C) Mounting the Receiver17
- D) Installing the Servos18
- E) Checking the Servo Function18
12 Programming the Remote Control19
- The System Setting Menu „System Setup20
- A) Model Memory Selection „Model Select21
- B) Model Name Setting „Model Name22
- C) Model Type Selection „Type Select23
- D) Copying Model Memory „Model Copy24
- E) Deleting Model Memory „Model Reset25
- F) Receiver Programming „RX Setup26
- Digital Coding „AFHDS 2A27
- Receiver Voltage „RX Battery28
- Failsafe Setting „Failsafe29
- Sensor List „Sensor List30
- Servo Control Frequency „Servos Freq31
- G) Operation as Trainer Transmitter „Trainer Mode32
- H) Operation as Student Transmitter „Student Mode33
- I) Control Stick Assignment „Sticks Mode34
- J) Display Brightness „LCD Brightness35
- K) Transmitter Software Version „Firmware Ver36
- L) Transmitter Software Update „Firmware Update37
- M) Reset to Factory Settings „Factory Reset38
- The Function Setting Menu „Functions Setup39
- A) Servo Direction Setting „Reverse40
- B) Servo End Deflection Setting „End Points41
- C) Servo Control/Test „Display42
- D) Encoder Assignment „Aux. Channels43
- E) Basic Trim „Subtrim44
- F) Dual Rate/Exponential Setting „Dual Rate/Exp45
- G) Throttle Curve Setting „Throttle Curve47
- H) Pitch Curve Setting „Pitch Curve49
- I) Swash Plate Servo Setting „Swash AFR51
- J) Mixer Programming „MIX53
- K) Delta Mixer „Elevon56
- L) V-Tail Mixer „V Tail58
- M) Gyro Sensitivity Setting „Gyroscope60
- N) Switch Assignment „Switches Assign62
- O) Throttle Switch „Throttle Hold63
15 Remote Control Operation64
16 Binding Function65
17 Maintenance and Care66
18 Declaration of Conformity (DOC)66
19 Disposal66
- A) General Information66
- B) Batteries and Rechargeable Batteries66
20 Troubleshooting67
21 Technical Data68
- A) Transmitter68
- B) Receiver68

Reely HT-6 - Page 52

Table of Contents

Related product manuals