Rigol DP2000 Series

To Next Page

To Previous Page

Environmental conditions

Overvoltage Categories OVC II

Operating Environment

For indoor use only and non-operating in

humid environment.

Warranty and Calibration Interval

Warranty and calibration interval

Warranty 3 years (excluding the accessories)

Recommended

calibration interval

Every 12 months

Note[1]:

• Unless otherwise stated, the specifications are applicable to all the channels of

the specified model.

• All parameters are measured at rear output terminals.

• Not applicable in series/parallel connection mode.

Note[2]: The accuracy parameters are acquired via calibration under 25℃ after 1-

hour warm-up.

Note[3]: The low range current mode is applicable to measurement of current lower

than 10 mA.

Note[4]: the time required for the output to change accordingly after receiving the

APPLy and SOURce commands.

Specifications

DP2000 User Guide

Main Page

Table of Contents3
Safety Requirement9
General Safety Summary9
Safety Notices and Symbols11
Measurement Category11
Ventilation Requirement12
Working Environment12
Care and Cleaning14
Environmental Considerations14
Product Overview16
Document Overview17
Quick Start19
General Inspection19
Appearance and Dimensions20
Front Panel20
Figure 4.1 Front View20
Figure 4.2 Side View20
Figure 4.3 DP2000 Front Panel21
Figure 4.4 DP2000 Output Terminals23
Rear Panel24
Figure 4.5 DP2000 Rear Panel24
Table 4.1 DP2000 Rear Panel Description24
User Interface25
Figure 4.6 User Interface26
Table 4.2 User Interface Description26
Connecting to Power27
Table 4.3 AC Input Power Specifications (Including AC Selector Setting)27
Power-On Inspection29
Connecting the Outputs29
Replacing the Fuse30
Table 4.4 Fuse Rating30
Using the Built-In Help System31
Figure 4.7 Help Interface31
Using the Protection Function33
Figure 5.1 CH1 Output Settings Interface33
Constant Voltage Output35
Constant Current Output38
Series/Parallel Connections39
Series Connections39
Figure 8.1 Series Output Interface40
Figure 8.2 External Series Circuit41
Parallel Connections42
Figure 8.3 Parallel Output Interface42
Figure 8.4 External Parallel Circuit44
Arb Function45
Figure 9.1 Arb Main Interface45
Setting Arb Properties46
Figure 9.2 Arb Settings Interface46
Arb Editor48
Figure 9.3 Arb Editor Interface48
Inserting a Single Point49
Editing Waveform Templates49
Figure 9.4 Template Editing Menu49
Table 9.1 Arb Parameters (Template)53
Delete55
Import and Export55
Enabling the Arb Output56
Figure 9.5 Arb Output Interface56
Analyzer57
Common Analysis57
Figure 10.1 Analyzer Main Interface57
Selecting Analysis Object58
Figure 10.2 Common Analysis Setting Interface58
Figure 10.3 Analysis Object Setting Menu58
Selecting Statistical Method59
Pulse Current Analysis60
Figure 10.4 Pulse Current Analysis Setting Interface60
Data Logging61
Figure 10.5 Pulse Current Analysis Interface61
Figure 10.6 Log Setting Interface61
Print Screen62
Label Control62
Trigger63
Figure 11.1 Digital Port Connections63
Trigger Input64
Figure 11.2 Trigger Setting Interface64
Figure 11.3 Trigger Input Setting Interface64
Trigger Output65
Figure 11.4 Trigger Output Setting Interface66
Store and Recall67
Figure 12.1 Disk Interface67
Select68
Save68
Read69
Delete69
Copy and Paste70
Utility71
System Settings71
Figure 13.1 Utility Interface71
Instrument Settings72
Figure 13.2 Instrument Settings Interface72
Table 13.1 Factory Default Values73
Display Options75
Sense Settings75
Figure 13.3 Display Options Interface75
Figure 13.4 Rear Panel Connections76
Figure 13.5 Sense Settings Interface76
Output Settings77
Track Mode77
Figure 13.6 Output Settings Interface77
Safe Mode78
Sampling Mode78
Output Connection79
Output off Mode79
Current Sampling Rate80
Interface Settings80
LXI Status80
Figure 13.7 Interface Settings80
Figure 13.8 LXI Status Interface81
LXI Setting82
Figure 13.9 LXI Settings Menu82
RS232 Setting84
Figure 13.10 RS232 Interface85
Table 13.2 RS232 Pin Definition85
USB Configuration86
Figure 13.11 RS232 Configuration Interface86
GPIB Configuration87
Figure 13.12 USB Configuration Interface87
Figure 13.13 GPIB Configuration Interface87
Option Settings88
Figure 13.14 Option Settings Interface88
Locking/Unlocking the Front Panel90
Remote Control92
Remote Control Via USB93
Remote Control Via LAN93
Remote Control Via GPIB (Optional)94
Remote Control Via RS23295
Figure 15.1 Search for the Available Device95
Figure 15.2 Confirm the Available Device95
Troubleshooting98
Specifications100
Appendix105
Appendix A: Accessories and Options105
Appendix B: Warranty105

Rigol DP2000 Series - Page 104

Table of Contents

Other manuals for Rigol DP2000 Series

Related product manuals