Robopac S6 - User Manual

94 pages

Save Page as PDF

To Next Page

USE AND MAINTENANCE MANUAL

ENG

Self propelled wrapping robot

ROBOT S6

Translation of the original instructions

Code:

3709301826.1

Edition: 0117

________

SERIAL NUMBER __________

__________________________________________________________________________________________________________

TTENTION

Read and understand these instructions before usin

the machine.

Keep this handbook for further consultation

ROBOPAC S.p.A.

Main Page

Questions and Answers

A
Anthony GonzalezAug 21, 2025
What to do if Robopac Stretch Wrapping Systems displays 'E80 - ALL. BATTERY CHARGER' error?
- R
  Richard PattonAug 21, 2025
  If your Robopac Stretch Wrapping Systems shows 'E80 - ALL. BATTERY CHARGER', this indicates a battery charge failure. You should check the battery charger and refer to the wiring diagram.
R
rbyrdSep 3, 2025
What to do if Robopac Stretch Wrapping Systems displays 'E31 - CARR. DRIVER OVERTEMP' error?
- L
  Lawrence EspinozaSep 3, 2025
  If your Robopac Stretch Wrapping Systems displays the error 'E31 - CARR. DRIVER OVERTEMP. - CARR. DRIVER SHORT CIRCUIT. - CARR. DRIVER UNDERVOLT. - CARR. HEAT SINK OVERTEMP. - CARR. CURRENT LIMIT.', it indicates a carriage lift motor failure. Check the motor and refer to the wiring diagram.
C
Crystal Rogers MDSep 1, 2025
What to do if Robopac Stretch Wrapping Systems displays 'E35 - TRACTION OVERCURRENT' error?
- W
  Wesley NelsonSep 1, 2025
  If your Robopac Stretch Wrapping Systems shows the error 'E35 - TRACTION OVERCURRENT', it means the motor has been working heavily for an exceedingly long period. Check the motor operation, ensure the machine is free to move, and refer to the relevant electric diagram.
E
Elizabeth Gomez MDAug 31, 2025
What to do if Robopac Stretch Wrapping Systems displays 'E30 - TRACTION DRIVER OVERTEMP' error?
- T
  Tammie RussellAug 31, 2025
  If your Robopac Stretch Wrapping Systems displays the error 'E30 - TRACTION DRIVER OVERTEMP - TRACTION DRIVER SHORT CIRCUIT - TRACTION DRIVER UNDERVOLT - TRACTION HEAT SINK OVERTEMP - TRAZ. CURRENT LIMIT', it indicates a drive motor failure. Check the motor and refer to the wiring diagram.
B
Bethany MerrittAug 29, 2025
What to do if Robopac S6 displays 'E81 - H.M.I. COMUNIC. FAULT' error?
- R
  Robyn HendersonAug 29, 2025
  If your Robopac Stretch Wrapping Systems shows 'E81 - H.M.I. COMUNIC. FAULT', it means that the cable is unplugged or the touch screen is faulty. You should check the operation of the touch screen panel and refer to the relevant electric diagram.
L
Laura GonzalezAug 27, 2025
What to do if Robopac Stretch Wrapping Systems displays 'E60 - ALL. BROKEN FILM'?
- L
  Lauren PhillipsAug 27, 2025
  If the Robopac Stretch Wrapping Systems displays the error 'E60 - ALL. BROKEN FILM', it means that the film has broken or the reel is empty. To fix it, insert a new film or replace the reel.
I
itorresAug 26, 2025
What to do if Robopac S6 displays 'E02 - BUMPER' error?
- B
  Brian FergusonAug 27, 2025
  If your Robopac Stretch Wrapping Systems shows an 'E02 - BUMPER' error, it indicates that the bumper hit an obstacle in the working area. Remove the obstacle and then press the “Reset” push-button to clear the error.
E
ejohnsonAug 25, 2025
What to do if Robopac S6 shows 'E01 - EMERGENCY STOP'?
- S
  Susan MartinezAug 25, 2025
  If the Robopac Stretch Wrapping Systems displays the error 'E01 - EMERGENCY STOP', it means the emergency pushbutton is in a locked position. To resolve this, reset the button and then press the Reset button.
S
shawnriceAug 23, 2025
What to do if Robopac S6 displays 'E90 - BATTERY LOW' error?
- U
  uboydAug 23, 2025
  If the Robopac Stretch Wrapping Systems displays the error 'E90 - BATTERY LOW', it means the battery has run down to the safety level, and the machine will stop. Transport the machine to the nearest charge point using the manual forward/back buttons on the steering arm; see "control description".