Roland M-480 - Page 49

49
Input channel operations
Input channel operations
AUX SENDS, MTX SENDS
fig.ScrChSends.eps
Here you can adjust the sends to the AUX or MTX buses.
● AUX sends, MTX sends
The AUX sends, MTX sends are organized as follows:
fig.ScrChSendField.eps
To show the MTX sends or AUX sends, press [F6 ( MTX SENDS)]
or [F6 ( AUX SENDS)].
AUX/MTX number
This indicates the AUX/MTX number.
AUX/MTX name
This indicates the AUX/MTX name.
Send level bar
This adjusts the send level to the AUX/MTX bus in a range of
-Inf dB– +10.0 dB.
The color of the send level bar indicates the send point and
the status of the send switch as follows:
● AUX/MTX pan slider
fig.ScrChSendField2.eps
If the AUX/MTX send-destination is stereo-linked, this lets
you adjust the left/right panning of the audio signal in a
range of L63–R63. This is shown in the area of the odd-
numbered AUX/MTX send.
For details, refer to “AUX/MTX send operations (CH1–48, RTN1–
6)” (p. 84).
DIRECT OUT point
fig.ScrChDirGuide.eps
You can choose one of the following as the position from
which the channel’s signal is taken as the direct out signal:
PAN
fig.ScrChPan.eps
LCR button
This button specifies how signals are sent from the channel
to MAIN L/R and MAIN C.
CENTER
This specifies the proportion of the signal that is sent to
MAIN C when PAN is at C (center) as a value in a range of
0%–100%. This is valid when the LCR button is on.
fig.Pan_LCR.eps
PAN
• When LCR button is off
This adjusts the left/right panning of the audio signal sent to
the MAIN L/R buses in a range of L63–R63.
• When LCR button is on
This adjusts the left/center/right panning of the audio signal
sent to the MAIN L/R/C buses in a range of L63–R63.
Blue
send point is PRE EQ or PRE FADER
Green send point is POST FADER
Gray Send switch is off
9
1 2
3
1
2
3
PRE PHASE
Take the pre-phase signal.
PRE EQ Take the pre-EQ signal
PRE FADER Take the pre-fader signal
POST FADER Take the post fader signal
OFF The signals sent to MAIN L/R and MAIN C can be
individually turned on/off by using the LR button and C
button.
ON PAN will operate across the three outputs MAIN L,
MAIN C, and MAIN R. The convergence of the sound to
MAIN C can be adjusted by CENTER. The signals sent to
MAIN L/R and MAIN C can be collectively turned on/off
by the MAIN button.
0% No signal will be sent to MAIN C.
100% When PAN is set to C, the signal will be sent only to MAIN
C.
10
11
1
2 3
1
2
LC
PA N
LEVEL
R
t
o
L
E
F
T
t
o
R
I
G
H
T
Center 0%
LC
PA N
LEVEL
R
t
o
L
E
F
T
t
o
R
I
G
H
T
t
o
C
E
N
T
E
R
Center 50%
LC
PA N
LEVEL
R
t
o
L
E
F
T
t
o
R
I
G
H
T
t
o
C
E
N
T
E
R
Center 100%
3
M-480_e.book 49 ページ ２０１１年３月２日 水曜日 午前９時２０分