Sharp MX-2300 G - Page 143

MX-2300/2700 N/G SIMULATION 7 – 37
<Set item C (TONER END) control content>
27
27-1
Purpose : Operation test/Check
Function (Purpose) : Used to set whether the detection of com-
munication error with RIC (U7-00) is dis-
abled or not.
Section : Communication (RIC/MODEM)
Item : Specifications (Operation mode)
Operation/Procedure
1) When the machine enters Simulation 27-01, following the
screen is displayed.
2) Enter the set value with 10-key.
3) When [OK] button is pressed, and the current set value is
saved to EEPROM and RAM.
After completion of setting, [OK] button returns to the normal
display.
* When [OK] button, [COLOR], or [BLACK] key is pressed, the
current set value is saved to EEPROM and RAM.
<Setting range and default value of each value>
27-2
Purpose :Setting
Function (Purpose) : Used to set the FSS function (Password,
HOST server TEL number).
Section : Communication (RIC/MODEM)
Item : Data (User data)
Operation/Procedure
1) When the machine enters Simulation 27-02, the screen is dis-
played.
2) Select a desired button.
The button is highlighted and the value is displayed.
3) Enter the set value with 10-key. The entered value is displayed
at "NEW."
* Press [C] key to clear the entered value.
4) When [SET] button is pressed, the entered value is set.
When the entered value is set, it is displayed in "PRESENT:"
<Item and content descriptions>
27-4
Purpose :Setting
Function (Purpose) : Used to set the FSS functions (initializing,
call, toner order auto send).
Section : Communication (RIC/MODEM)
Item : Data (User data)
Operation/Procedure
1) When the machine enters the simulation, the following screen
is displayed.
2) Select an item to be set with [↑] and [↓] buttons.
The highlighted section of the set value is changed and the
value is displayed in the setting area.
* When there is an item over [↑], the display becomes active
and shifts to another item.
When there is no item over [↑], the display grays out and the
operation is disabled.
When there is an item under [↓], the display becomes active
and shifts to another item.
When there is no item under [↓], the display grays out and
the operation is disabled.
3) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
4) When [OK] button is pressed, it is highlighted and the current
set value is saved to EEPROM and RAM.
After completion of setting, [OK] button returns to the normal
display.
* When [OK] button, [COLOR], or [BLACK] key is pressed, the
current set value is saved to EEPROM and RAM.
C TONER END 1 Operation is enabled
when TONER END.
(*1)
1 to 3 2
2 Operation is stopped
when TONER END.
(*2)
3 Operation is stopped
when TONER END.
(*3)
DTONER END
COUNT
Used to set the number of
detection of toner end.
1 to 5 3
TONER END flag detection CRUM ID machine history check
*1 No detection No detection
*2 No detection Detection
*3 Detection Detection
Item Display Content
Setting
range
Default
value
A DISABLE 0: YES (U7-00) Not
detected
YES 0 to 1 0 0: Not
detected
1: NO NO 1
Item Display Content
Setting
range
Default
value
0
A
:
A㧦 0
B㧦 0
㧧
TONER PREPARATION(0:YES 1 :NO)
㧧 TONER NEAR END (0:YES 1: NO)
C㧦 2 㧧 TONER END
D㧦 3 㧧 TONER END COUNT
SIMULATION NO.26-69
TONER NEAR END SETTING
0
0 1
OK
TEST
CLOSE
㩷㩷㩷㩷㩷㩷㩷㩷㩷
A
:
A㧦 0
㧧DISABLE㧦
NO
SIMULATION NO.27-01
DISABLING OF U7-00 TROUBLE
0
㨇 0㨪 1㨉
OK
TEST
0
CLOSE
Display Description Number of digits
USER FAX_NO. Sender registration number Max. 16 digits
SERVA TEL_NO. HOST server TEL number Max. 16 digits
 USER FAX_NO.  SERVA  TEL_NO
SIMULATION  NO.27-02
TEST
FSS FUNCTION SETUP㧔INPUT㧕
1/1
00000000000000000000000000000001
㧦
㧦
㧦
0
PRESENT
NEW
SET
CLOSE