MX-2300/2700 N/G SIMULATION 7 – 44
41
41-1
Purpose : Operation test/Check
Function (Purpose) : Used to display the operating state of the
document sensor.
Section : Other
Item : Operation
Operation/Procedure
1) When the machine enters Simulation 41-01, the following
screen is displayed to show the sensor status change.
* When each sensor is turned ON, the corresponding sensor
name is highlighted.
<Sensor name>
41-2
Purpose : Operation test/Check
Function (Purpose) : Used to adjust the detection level of the
document size sensor.
Section : Other
Item : Operation
Operation/Procedure
1) When the machine enters Simulation 41-02, the following
screen is displayed.
Press [EXECUTE] button without a document on OC.
[EXECUTE] button is highlighted and the sensor level setting
without document is performed.
2) The sensor level setting without document is completed.
Set A3 (11" x 17") paper on OC and press [EXECUTE] button.
The sensor level setting with document detection is performed.
3) After completion of sensor level setting with document, the
message is displayed to show the adjustment has been suc-
cessfully completed. (In case of an error, the error message is
displayed with the failed sensor name.)
<Document sensor names, adjustment ranges and default val-
ues>
41-3
Purpose : Operation test/Check
Function (Purpose) : Used to display the document sensor
detection level (A/D) in real time and to dis-
play the threshold value adjusted with SIM
41-2 in [ ] beside the sensor name.
Section : Other
Item : Operation
Operation/Procedure
1) When the machine enters Simulation 41-03, the following
screen is displayed.
* ON/OFF detection of the OCSW sensor and the A/D value
check of each PD sensor are performed in real time.
<Display content>
* In an actual control, the A/D value is sent by polling at a regular
interval from the SCU or the controller.
Code (Display) Sensor name
OCSW Original cover SW
PD1 Document detection 1
PD2 Document detection 2
PD3 Document detection 3
PD4 Document detection 4
PD5 Document detection 5
PD6 Document detection 6
PD7 Document detection 7
0
PD SENSOR CHECK
1/1
CLOSE
SIMULATION
NO.41
㧙
01
TEST
1/1
OCSW
PD1 PD2 PD3
PD4
PD5 PD6 PD7
Sensor name Content Set range Default value
PD1 Document sensor 1 0 – 255 128
PD2 Document sensor 2
PD3 Document sensor 3
PD4 Document sensor 4
PD5 Document sensor 5
PD6 Document sensor 6
PD7 Document sensor 7
Display Content Range
OCSW Original cover SW 0 – 1 ("1": Close)
PD1 Document detection 1 0 – 255
PD2 Document detection 2 0 – 255
PD3 Document detection 3 0 – 255
PD4 Document detection 4 0 – 255
PD5 Document detection 5 0 – 255
PD6 Document detection 6 0 – 255
PD7 Document detection 7 0 – 255
SIMULATION NO.41-02
TEST
DOCUMENT SIZE PHOTO-SENSOR SETUP
EXECUTE
0
CLOSE
WITH THE ORIGINAL COVEROPENED, TURN ON THE EXECUTE
KEY WITH THE ORIGINAL ON THE ORIGINAL TABLE.
OCSW
SIMULATION
NO.41
03
TEST
PD SENSOR DISPLAY
1
:
PD5[㪁㪁㪁]
㪁㪁㪁㩷
:
PD1[㪁㪁㪁]
㪁㪁㪁㩷
:
PD6[㪁㪁㪁]
㪁㪁㪁㩷
:
PD2[㪁㪁㪁]
㪁㪁㪁㩷
:
PD7[㪁㪁㪁]
㪁㪁㪁㩷
:
PD3[㪁㪁㪁]
㪁㪁㪁㩷
:
PD4[㪁㪁㪁]
㪁㪁㪁㩷
:
1/1
0
CLOSE
To Next Page
Loading...
