MX-2300/2700 N/G SIMULATION 7 – 55
<CRUM destination code list>
44-12
Purpose : Adjustment/Setup/Operation data output/
Check (Display/Print)
Function (Purpose) : Used to check the sampling toner image
patch density data in the image forming
section correction (high density process
correction). (This simulation is used to
check whether the correction is normally
executed or not.)
Section :Process
Item : Data (Machine condition)
Operation/Procedure
1) Change the page with [↑] [↓] buttons.
* If there is a page over [↑], an active display is shown and the
page moves up. If there is no page upward, the display
grays out and the operation is invalid.
If there is a page under [↓], an active display is shown and
the page moves down. If there is no page downward, the
display grays out and the operation becomes invalid.
2) Change the display with the following buttons:
[TARGET] button: Display of each color target
[PATCH] button: Display of patch sampling data
* When [CLOSE] button is pressed, the display shifts to the copy
basic screen of simulation.
* Copying can be performed also by pressing [COLOR]/[BLACK]
key.
<Display item and content description>
* PATCH item: If the patch is converged to the target range in less
than 10 times of patch acquisition, "0" is displayed in the other
display items.
* When [PATCH] button is pressed, the following page is dis-
played.
• n = 1 to 2 Page 1
• n = 3 to 4 Page 2
• n = 5 to 6 Page 3
• n = 7 to 8 Page 4
• n = 9 to 10 Page 5
OTHER 9/10 CRUM Left DESTINATION Machine side control CRUM
destination
Refer to
<CRUM
destination
code list>.
CRUM
information
MODEL TYPE Machine model type 0 to 1 0
Right CRUM DEST_K CRUM destination Refer to
<CRUM
destination
code list>.
CRUM
information
CRUM DEST_C
CRUM DEST_M
CRUM DEST_Y
10/10 CNT Left PROCON COUNT HV Number of execution of high density
process control
0 to 99999999 0
PROCON COUNT HT Number of execution of half tone
process control
0 to 99999999 0
Mode Page number Display item (*: correction value) Content description Display range
Default
value
Display code No. Destination Control specification
01 A AR control
02 B EX Japan AR control
03 C AR control
04 B Japan AR control
05 E AR control
OTHER
SIMULATION NO.44-09
TEST
PROCON DATA DISP (PROCON/NORMAL(M))
CLOSE
BLACK : GB_ 230/630 DV_ 0/430
CYAN : GB_ 230/630 DV_ 0/430
MAGENTA : GB_ 230/630 DV_ 0/430
YELLOW : GB_ 230/630 DV_ 0/430
BLACK : GB_ 230/600 DV_ 0/400
CYAN : GB_ 230/600 DV_ 0/400
MAGENTA : GB_ 230/600 DV_ 0/400
YELLOW : GB_ 230/600 DV_ 0/400
1/2
CPY/PRN
0
Item Display item
Content
description
Display
range
Default
value
TARGET
(Page 1)
CARB DATA Calibration plate
sensor value
1 to 255 108
SEAL ADJ
DATA
Jig patch seal
sensor value
1 to 255 108
ADK_SL (K) Developing
characteristics
gradient coefficient
–9.99 to 9.99 0
ADK_INT (K) Developing
characteristics
intercept
coefficient
–999.9 to
999.9
0
ID(K) Sensor target
value
0.00 to
255.00
0.00
ID(CMY) Color sensor
target set value
0.00 to
255.00
0.00
PATCH
(Page 1
to 5)
N-1 Patch data nth
front patch
(n = 1 to 10)
0 to 255 0
N-2 Patch data nth
center patch
(n = 1 to 10)
0 to 255 0
N-3 Patch data nth rear
patch
(n = 1 to 10)
0 to 255 0
PATCH
TARGET
SIMULATION NO.44-12
TEST
PATCH/TARGET DATA DISPLAY
CARB DATA : 108
SEAL ADJ DATA : 108
ADK SL(K) : 0.00
ADK INT(K) : 0.0
TARGET(K) : 0.00
TARGET(C) : 0.00
TARGET(M) : 0.00
TARGET(Y) : 0.00
1/1
0
To Next Page
Loading...
