Name: SoundCraft Vi4
Brand: SoundCraft
Rating: 5 (1 reviews)

To Next Page

To Previous Page

Soundcraft Vi6™ User GuidePage 12 - 4

This page allows the user to patch the oscillator to outputs on the StageBox and the Local Rack, to MADI

channels, or to the key inputs of the dynamics units on the input channels 1-64.

The user selects the appropriate screen by selecting one of the following touch screen buttons: <Dynamics

Key>, <MADI>, <StageBox> or <Local>.

Figure 12-4: Oscillator Output Patch Page.

Default Chapter1
- User Guide1
- Table of Contents3
Introduction11
- Safety Notices11
- Safety Symbol Guide11
- Important Safety Warnings12
  - Warnings13
- Working Safely with Sound14
- Warranty14
- Soundcraft Vi6™ FEATURES and SPECIFICATIONS15
- Console Overview18
System Components23
- System Hardware Overview24
- Note on Installation of the Cooling Fans/Filters25
- The Console Rear Connectors26
  - Mains Power Supply Inlet26
  - Audio and Data Rearcon26
- Local Rack28
- Stage Box35
- Connecting the Parts of the System38
  - (With Cat 5 Breakout Panel Fitted)38
- Connecting the Parts of the System40
  - (Without Cat 5 Breakout Panel Fitted)40
- General Rules43
Operation Overview43
- General Rules43
- Conventions Used in this Manual43
- Screens43
  - Screen Colour Codes44
- Vistonics II™ Knobs45
- Audio Function States45
- Momentary/Latching Control Action45
- Labelling46
  - General46
  - Channel Labels47
- Solo/Sel Keys46
- Bus Configuration48
- Gang49
Input51
- Signal Flow51
- Input Channel Strip52
- Input Channel Touch Fields53
  - Change a Parameter of an Input Channel53
- Input54
- Stereo Configuration56
- Equaliser58
- Dynamics60
- Bus64
- Panning65
- Audio Format67
Outputs71
- Signal Flow71
- General72
  - L,R & C Master Processing73
- MASTER EQ LINKING (V2.0 Software and Above)74
  - Default Settings74
- Master Bay Output Strips75
  - Bus Master Processing76
- Input Bay Strip Using [All Busses]77
- Master Bay Vistonics™ Encoders & Keys78
  - VST Key Function78
- Changing Output Bus Parameters79
  - Changing a Parameter of a Bus79
- Equaliser80
- Dynamic81
- Pan82
Matrix83
- Signal Flow83
- Function83
  - Adjusting a Matrix Send Level85
- Matrix Configuration85
  - SOURCE Field85
  - MTX Point Field86
Encoders87
- General Introduction87
- Channel Encoders88
- Channel Vst Encoder 1& 289
  - VST Encoder Priority89
  - Changing Encoder Function90
- Master Bay Panel Encoders91
- Master Bay Vst Encoders91
  - Master Vistonics Switch Function Panel92
Layering (Fader Pages)93
- General93
- Inputs93
  - Temporary Layer94
- Outputs95
Vca & Mute Groups99
- Vca/Mute Group Indication99
- Mute Group Master Switches100
- Vca Control Group Behaviour100
- Audio Behaviour100
- ASSIGNING Vcas101
- Assigning Mute Groups101
- Assigning Vcas and Mute Groups to Output Channels101
- Vca Groups When Aux Sends Are Controlled by Channel Faders101
  - Procedure102
Patch System103
- Signal Flow103
- Overview104
- General Rules104
- Input105
  - Patch a Source to an Input Channel106
  - Using a Spare MIC for Several Inputs106
- Output107
  - Patch a BUS to an OUTPUT107
- Insert108
  - Patching an Insert Point to an Input Channel108
  - Stereo Inserts109
- Direct out110
- Key Signal111
- Matrix112
- Tie Lines113
Monitoring115
- Signal Flow115
- Function115
- Desk View116
- Monitor Setup Page118
- Monitor Setup Sub-Page122
  - Output solo Selection124
- Solo System125
Talkback & Oscillator131
- Desk View131
  - Setup Key131
- Setup132
Metering137
- Input Channel Meter137
- Bus Master Meters138
- Master Output Meters138
- Monitor Meters138
- Scale138
- Meters on the Master Section Screen139
  - Touch Selection139
- Peak Hold140
- Ballistics140
Main Menu141
- Main141
  - SECURITY Field141
  - BRIGHTNESS Control141
- Show142
- Gpio143
- Sync144
- Tie Lines145
- Fx147
- MIDI147
- Log148
- Settings149
  - Point149
  - Deactivate Fader Touch149
- System Monitoring150
Snapshots and Cues155
- Front Panel Display and Controls155
- Setup157
  - Snapshop Pool157
  - Cue List157
- Managing Shows158
  - Hard Drive158
  - Usb Data Storage Device159
- Recorded Data160
Gpio163
- Configuration163
  - GPI VST Keys & Encoders164
  - GPO VST Keys & Encoders164
- Hardware166
  - Schematic Diagram166
  - Pin Lists167
SOUNDCRAFT Faderglow169
- General169
- Colour Code169
  - Memory Stick171
Copy, Paste & Libraries171
- Introduction171
- Console Control Keys171
- Copy & Paste Principles172
- Data Selection & Indicators172
- Parameters Not Included in Channel & Bus Copy Modes173
- Copying Channel or Bus Parameters173
- Copying a Bus Master Including All Channel Send Levels173
- Channel Copy: Items Not Included in Copy with Sel Button174
- Bus Output Copy: Items Not Included in Copy with Sel Button174
- Example: Copying a Whole Channel, Including the 'In1 Patch' Parameter174
- Copying Fx Parameters175
- Libraries177
- Navigating and Managing Libraries179
- Copy to Library181
- Paste from Library182
- Exporting and Importing Libraries183
SOUNDCRAFT Vi6™ FEATURES and SPECIFICATIONS185
- Audio Channels185
- I/O Capability185
- Miscellaneous186
- Channel Processing186
  - Inputs186
  - Ouputs186
- Control Surface187
  - Inputs187
  - Outputs187
    - Misc187
- Vi6 TYPICAL SPECIFICATIONS188
Block Diagram191
VI Processor™ Card191
- General191
  - LEXICON® Effects191
  - BSS® Graphic Equalisers191
- LEXICON® Effects Format191
- FX Overview Page192
- Snapshot Integration192
- Tap193
- ASSIGNING F1-6 KEYS to FX TAP TEMPO (V2.0 Software and Above)193
  - Changing the Assignment of F-Keys to TAP Function194
- Assigning Fx Processors194
- Fx Type201
- Fx Descriptions203
- Bss® Graphic Equalisers211

Brand	SoundCraft
Model	Vi4
Category	Music Mixer
Language	English

SoundCraft Vi4 User Manual

Table of Contents

Other manuals for SoundCraft Vi4

Questions and Answers:

SoundCraft Vi4 Specifications

Related product manuals