e-STUDIO556/656/756/856(Ver03) © 2012 TOSHIBA TEC CORPORATION All rights reserved
ERROR CODE AND TROUBLESHOOTING
8 - 14
CBB0 Finisher related
service call
Stitch motor (rear) abnormality: The stitch motor (rear)
does not run normally or the rotational cam does not
move normally.
P. 8 - 1 07
CBC0 Alignment motor abnormality: The alignment motor does
not run normally or the alignment plate does not move
normally.
P. 8 - 1 08
CBD0 Guide motor abnormality: The guide motor does not run
normally or the guide does not move normally.
P. 8 - 1 08
CBE0 Paper folding motor abnormality: The paper folding motor
does not run normally or the paper folding roller does not
move normally.
P. 8 - 1 09
CBF0 Paper positioning plate motor abnormality: The paper
positioning plate motor does not run normally or the
paper positioning plate does not move normally.
P. 8 - 1 09
CC00 Sensor connector abnormality: Disconnection of each
connector of the guide home position sensor, paper
pushing plate home position sensor and paper pushing
plate leading position sensor is detected.
P. 8 - 110
CC10 Microswitch abnormality: Any of the inlet door switch,
delivery door switch and front cover closing detection
switch is opened while all the covers are closed.
P. 8 -111
CC20 Communication error between Finisher and Saddle Stitch
section: Communication error has occurred between the
finisher controller PC board and the saddle stitcher
controller PC board.
P. 8 - 113
CC40 Swing motor abnormality: The swing motor does not run
normally or the swing unit does not move normally.
P. 8 - 113
CC50 Horizontal registration motor abnormality: The horizontal
registration motor does not run normally or the puncher
does not move normally.
P. 8 - 115
CC60 Punch motor abnormality: The punch motor does not run
normally or the puncher does not move normally.
P. 8 - 116
CC80 Rear alignment motor abnormality: The rear alignment
motor is not rotating or the rear alignment plate is not
moving normally. [MJ-1029]
P. 8 - 117
CCC1 Communication error between Inserter Unit and Finisher P. 8-117
CCD1 Inserter EEPROM abnormality P. 8-117
CCE1 Inserter fan motor abnormality P. 8-118
CD00 Laser optical unit
related service call
Laser initialization time-out: Laser control does not end
within the initialization period.
[e-STUDIO756/856]
P. 8 - 1 01
CD10 Process related
service call
Cleaning brush drive motor abnormality: The cleaning
brush drive motor does not run normally when the power
is turned ON or the copying is started.
P. 8 - 1 21
CD20 Used toner transport motor abnormality: The used toner
transport motor does not run normally when the power is
turned ON or the copying is started.
P. 8 - 1 21
CD30 Recycle toner transport motor abnormality: The recycle
toner transport motor does not run normally when the
power is turned ON or the copying is started.
P. 8 - 1 21
CD40 Toner bag full P. 8-121
CD50 Fuser unit related
service call
Web motor signal path abnormality P. 8-94
CDE0 Finisher related
service call
Paddle motor abnormality: The paddle motor is not
rotating or the paddle is not rotating normally. [MJ-1029]
P. 8 - 118
CE50 Image quality
control related
service call
Temperature/humidity sensor abnormality: The output
value of the temperature/humidity sensor is out of the
specified range.
P. 8 - 1 22
CE90 Drum thermistor abnormality: The output value of the
drum thermistor is out of the specified range.
P. 8 - 1 22
Error code Classification Contents Troubleshooting
To Next Page
Loading...
