Vertiv NetSure M830B User Manual

Vertiv™ NetSure™ Control Unit (NCU) User Manual
82
Table 2.3
Alarm Name Alarm Description Action to Correct
Current10 High 1 Current Current 10 above High 1 limit.
Check why current is high.
Current10 High 2 Current Current 10 above High 2 limit.
SMDUE1 Temp 1 Not Used Temperature sensor port #1 on SMDUE1 is not used.
Temperature probe is enabled but not plugged in. … …
SMDUE1 Temp 10 Not Used Temperature sensor port #10 on SMDUE1 is not used.
SMDUE1 Temp 1 Sensor Fail Temperature sensor #1 on SMDUE1 failure. Replace temperature sensor.
Note: The alarm “Temp Sensor Fail” will occur if the
temperature probe fails internally or is not plugged in;
however, this alarm will be suppressed if “Temp Not
Used” alarm is active.
… …
SMDUE1 Temp 10 Sensor Fail Temperature sensor #10 on SMDUE1 failure.
Voltage1 Low1 Volt Alarm
Monitored Voltage1 is lower than the Low1 Volt Alarm
threshold.
Check why voltage is high or low.
Voltage1 Low2 Volt Alarm
Monitored Voltage1 is lower than the Low2 Volt Alarm
threshold.
Voltage1 High1 Volt Alarm
Monitored Voltage1 is higher than the High1 Volt Alarm
threshold.
Voltage1 High2 Volt Alarm
Monitored Voltage1 is higher than the High2 Volt Alarm
threshold.
… … …
Voltage10 Low1 Volt Alarm
Monitored Voltage10 is lower than the Low1 Volt Alarm
threshold.
Check why voltage is high or low.
Voltage10 Low2 Volt Alarm
Monitored Voltage10 is lower than the Low2 Volt Alarm
threshold.
Voltage10 High1 Volt Alarm
Monitored Voltage10 is higher than the High1 Volt
Alarm threshold.
Voltage10 High2 Volt Alarm
Monitored Voltage10 is higher than the High2 Volt
Alarm threshold.
TranVolt1 Low1 Volt Alarm
Monitored Transducer Voltage1 is lower than the Low1
Volt Alarm threshold.
Check why voltage is high or low.
TranVolt1 Low2 Volt Alarm
Monitored Transducer Voltage1 is lower than the Low2
Volt Alarm threshold.
TranVolt1 High1 Volt Alarm
Monitored Transducer Voltage1 is higher than the
High1 Volt Alarm threshold.
TranVolt1 High2 Volt Alarm
Monitored Transducer Voltage1 is higher than the
High2 Volt Alarm threshold.
… … …
TranVolt10 Low1 Volt Alarm
Monitored Transducer Voltage10 is lower than the Low1
Volt Alarm threshold.
Check why voltage is high or low.
TranVolt10 Low2 Volt Alarm
Monitored Transducer Voltage10 is lower than the
Low2 Volt Alarm threshold.
TranVolt10 High1 Volt Alarm
Monitored Transducer Voltage10 is higher than the
High1 Volt Alarm threshold.
TranVolt10 High2 Volt Alarm
Monitored Transducer Voltage10 is higher than the
High2 Volt Alarm threshold.
TranCurr1 Low1 Curr Alarm
Monitored Transducer Current1 is lower than the Low1
Curr Alarm threshold.
Check why current is high or low.
TranCurr1 Low2 Curr Alarm
Monitored Transducer Current1 is lower than the Low2
Curr Alarm threshold.
TranCurr1 High1 Curr Alarm
Monitored Transducer Current1 is higher than the
High1 Curr Alarm threshold.
TranCurr1 High2 Curr Alarm
Monitored Transducer Current1 is higher than the
High2 Curr Alarm threshold.

Vertiv NetSure M830B Specifications

General

Brand	Vertiv
Model	NetSure M830B
Category	Controller
Language	English