Vetus BOWB285 - Table of Contents

020814.02 3
Installation manual BOW PRO Series Thruster: BOWB285 - BOWB300 - BOWB320
1 Veiligheid ................................. 7
2 Inleiding
................................... 7
3 Installatieaanbevelingen
............ 8
3.1 Opstelling van de tunnelbuis ....... 8
3.2 Opstelling boegschroef in
tunnelbuis ................................. 8
3.3 Overgang van tunnelbuis naar
scheepsromp ............................. 9
3.4 Spijlen in de tunnelbuis-
openingen ................................. 9
3.5 Aanbrengen van de tunnelbuis .. 10
3.6 Aanbrengen van de gaten in de
tunnelbuis
............................... 10
3.7 Bescherming van de
boegschroef tegen corrosie ....... 10
4 Inbouw
................................... 11
4.1 Inleiding .................................. 11
4.2 Montage staartstuk en
tussenens .............................. 11
4.3 Eindmontage ........................... 12
5 Elektrische installatie
............... 13
5.1 De keuze van de accu ................ 13
5.2 Hoofdstroomkabels (accukabels) 13
5.3 Hoofdschakelaar ...................... 13
5.4 Zekeringen .............................. 13
5.5 Aansluiten hoofdstroomkabels
en congureren van de boeg-
en/of hekschroef ...................... 13
5.6 Aansluiten CAN-bus
(stuurstroom) kabels ................. 14
6 Storingzoeken
......................... 14
6.1 CAN-bus system ....................... 14
6.2 Boegschroenstallatie ............... 14
7 Technische gegevens
............... 15
Inhoud Content Inhalt
1 Safety ..................................... 16
2 Introduction
............................ 16
3 Installation recommendations
.. 17
3.1 Positioning of the thruster tunnel 17
3.2 Positioning of the bow thruster
in the thrust-tunnel ................... 17
3.3 Connection of thrust tunnel to
ship’s hull ................................ 18
3.4 Grid bars in the tunnel openings . 18
3.5 Installation of the thrust tunnel .. 19
3.6 Drilling the holes in the thrust-
tunnel ..................................... 19
3.7 Protection of the bow thruster
against corrosion
...................... 19
4 Installation
.............................. 20
4.1 Introduction ............................ 20
4.2 Installation tailpiece and
intermediate ange .................. 20
4.3 Final assembly. . . . . . . . . . . . . . . . . . . . . . . . . . 21
5 Electrical installation
................ 22
5.1 Choice of battery ...................... 22
5.2 Main power cables (battery
cables) .................................... 22
5.3 Main switch ............................. 22
5.4 Fuses ...................................... 22
5.5 Connecting the main power
cables and conguring the bow
and/or stern thruster ................. 22
5.6 Connecting CAN bus (control
current) cables ......................... 23
6 Troubleshooting
...................... 23
6.1 CAN bus system ....................... 23
6.2 Thruster installation .................. 23
7 Technical data
......................... 24
8 Hoofdafmetingen
................... 106
9 Aansluitschema’s
.................... 107
10 Accucapaciteit, accukabels
...... 114
8 Principal dimensions
............... 106
9 Wiring diagrams
..................... 107
10 Battery capacity, battery cables
114
1 Sicherheitsbestimmungen
....... 25
2 Einleitung
............................... 25
3 Einbauhinweise
....................... 26
3.1 Aufstellung vom tunnelrohr ....... 26
3.2 Aufstellung der Bugschraube
ins Tunnelrohr .......................... 26
3.3 Übergang vom tunnelrohr zum
schisrumpf ............................. 27
3.4 Gitterstäbe in den
Tunnelrohrönungen ................ 27
3.5 Anbringen vom Tunnelrohr ........ 28
3.6 Anbringen der Löcher ins
Tunnelrohr
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.7 Korrosionsschutz der
bugschraube ........................... 28
4 Einbau
.................................... 29
4.1 Einleitung ................................ 29
4.2 Befestigung des
Unterwasserteils und des
Zwischenansches .................... 29
4.3 Endmontage ............................ 30
5 Stromversorgung
.................... 31
5.1 Wahl des Akku ......................... 31
5.2 Hauptstromkabel (Akkukabel) .... 31
5.3 Hauptschalter .......................... 31
5.4 Sicherungen ............................ 31
5.5 Anschließen der
Hauptstromkabel und
Konfigurieren des Bug- und/
oder Heckstrahlruders ............... 31
5.6 Anschließen von CAN-Bus
(Steuerstrom)-Kabeln ................ 32
6 Fehlerbehebung
...................... 32
6.1 CAN-Bus-System ...................... 32
6.2 Bugstrahlruder-Einbau .............. 32
7 Technische daten
..................... 33
8 Hauptabmessungen
............... 106
9 Schaltplan
.............................. 107
10 Akkukapazität, akkukabel
....... 114