Xerox WorkCentre 4265

January 2016
2-81
WorkCentre WorkCentre 4150/4250/4260WorkCentre 4150/4250/42604150/
12-500, 12-600, 610
Status Indicator RAPs
12-500 Full Stack RAP
12-500 The machine has detected that the finisher output tray is full.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
NOTE: The main PWB has test points. The location of the test points is shown on the following
PJ location illustrations:
• 4150 Main PWB.
• 4250/4260 Main PWB.
• 4265 Main PWB.
Refer to(4150) Wiring Diagram 8, (4250/4260) Wiring Diagram 17 (4265) Wiring Diagram 33.
Perform the following:
1. Remove all documents from the finisher output tray.
2. Check that the stacker top sensor actuator, PL 12.45 Item 9 moves freely and is not dam-
aged.
3. Enter dC330 code 12-840. Check the stacker top sensor (Q12-840), PL 12.45 Item 8.
4. Check the wiring between the stacker top sensor and J8 on the Finisher PWB. If neces-
sary, install a new stacker top sensor, PL 12.45 Item 8.
5. (4150) Refer to Wiring Diagram 8. Check for +24V at pins 14 and 16 on CN27 on the Main
PWB. If +24V is not available, perform the following:
• Check the wiring between pins 13 and 15 on CON71 on Power Supply Unit 1 and
pins 14 and 16 on CN27 on the Main PWB.
• Install a new power supply unit 1, PL 1.10 Item 3.
• Perform the OF5 Main PWB Check RAP.
6. (4250/4260) Refer to Wiring Diagram 17. Check for +24V at pins 13 and 14 on CN18 on
the Main PWB. If +24V is not available, perform the following:
• Check the wiring between pins 13 and 14 on CON71 on Power Supply Unit 1 and
pins 13 and 14 on CN18 on the Main PWB.
• Install a new power supply unit 1, PL 1.15 Item 3.
• Perform the OF5 Main PWB Check RAP.
7. (4265) Refer to Wiring Diagram 33. Check for +24V at pins 3, 4, 5 and 6 on CN33 on the
Main PWB. If +24V is not available, perform the following:
• Check the wiring between pins 1, 3, 5, and 7 on CON3 on Power Supply Unit 1 and
pins 3, 4, 5 and 6on CN33 on the Main PWB.
• Install a new power supply unit 1, PL 1.15 Item 3.
• Perform the OF5 Main PWB Check RAP.
8. Check that the finisher PWB DIP switch settings are correct. Refer to the 12A
Finisher
PWB DIP Switch Settings RAP.
9. If necessary, install a new finisher PWB, PL 12.10 Item 8.
12-600, 610 Staple Cartridge Fault RAP
12-600 The machine has detected that a staple cartridge is not installed.
12-610 The machine has detected that the staple cartridge is empty.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Refer to Wiring Diagram 16. Perform the following:
1. Open the finisher front door. Check that the staple refill, PL 12.35 Item 5 is not empty.
Check that the staple refill, PL 12.35 Item 5 and stapler cartridge, PL 12.35 Item 4 are
installed correctly.
2. Check the wiring between the stapler assembly, PL 12.35 Item 2 and J9 on the Finisher
PWB.
3. If necessary, install new components:
• Staple refill, PL 12.35 Item 5.
• Stapler cartridge, PL 12.35 Item 4.
• Stapler assembly, PL 12.35 Item 2.
• Finisher PWB, PL 12.10 Item 8.