Xerox WorkCentre 4265

January 2016
v
WorkCentre WorkCentre 4150/4250/42604150/4250/4260WorkCentre 4150/
Change History
Introduction
• 10-500 Fuser Warning RAP
• 10-600, 610 Envelope Mode Error RAP
• 16-100 Immediate Image Overwrite RAP
• 17-900 802.1X Authentication Error RAP
• 0F5 Main PWB Check RAP
• REP 1.4 Power Supply Unit 1 and HVPS (4260)
• REP 1.5 Main PWB (4260)
• REP 1.6 Power Supply Unit 2 (4260)
• REP 2.2 User Interface Assembly (4260)
• REP 4.3 Main Drive Assembly (4260)
• REP 5.3 DADF (4260)
• REP 5.4 DADF Top Cover Assembly and Document Present Sensor (4260)
• REP 5.5 DADF Feed Roll Assembly (4260)
• REP 5.6 DADF Input Tray Assembly and Document Length Sensor (4260)
• REP 5.7 DADF document transport assembly (4260)
• REP 5.8 DADF Exit Motor Assembly (4260)
• REP 5.9 DADF Pickup Clutch and Registration Clutch (4260)
• REP 5.10 DADF Scan Motor Assembly (4260)
• REP 5.11 DADF Gate HP Sensor (4260)
• REP 5.12 DADF Pickup Guide Assembly and Sensors (4260)
• REP 5.13 DADF Document Path Sensors (4260)
• REP 7.5 HCF Feed Assembly and Sensors
• REP 7.6 HCF Paper Transport Sensors and Transport Roll Gear
• REP 7.7 Tray 2, 3 and 4 Feed Assembly and Sensors
• REP 9.4 Xerographic Module Connector (4260)
• REP 9.5 Toner Cartridge Connector (4260)
• REP 10.7 Fuser Assembly Components (4260)
• REP 10.8 Fuser Connector (4260)
• REP 11.1 Stapler Assembly and Interlock switch
• REP 14.3 Scanner Assembly (4260)
• REP 14.4 Scanner Components (4260)
• ADJ 14.1 Shading Adjustment
• Wiring Diagram 17 (4260)
• Wiring Diagram 18 (4260)
• Wiring Diagram 19 (4260)
• Wiring Diagram 20 (4260)
• Wiring Diagram 21 (4260)
• Wiring Diagram 22 (4260)
• Wiring Diagram 23 (4260)
• Wiring Diagram 24 (4260)
• Wiring Diagram 25 (4260)
• Wiring Diagram 26 (4260)
• Wiring Diagram 27 (4260)
• Wiring Diagram 28 (4260)
• Wiring Diagram 29 (4260)
• Wiring Diagram 30 (4260)
• Wiring Diagram 31 (4260)
The following bulletins, ETI and TIPs are included:
• 498913 SIM card reader not reading PEK
• 512014 Machine will not come to ready to copy
• 532479 Align user interface touch screen to display / menu buttons
• 546374 Shading adjustment difficult to locate
• 548122 Machine does not turn on / possible rebooting / +more symptoms
• 561448 Odd or strange fault code not in documentation
• 573078 System unavailable
• 573672 Scanner locked UI message
• 576470 Black configuration pages
• 590705 Machine will not boot machine doesn’t start
• 590929 Fax jobs locked in queue showing pending status
• 610135 Scan to email stuck in the transferring state
• 611748 Bypass tray misfeeds
• 616372 Bypass tray jams
• 621058 Squeak noise from the fuser module
• 630080 Grinding noise at exit area
• 640366 Copy white bands lead edge to trail edge DADF only
• 640408 4150 Ghost jams from trays
• 649498 Interrupt key and clear all key item numbers reversed in PL
• 668426 Printing solid black pages at power on
• 673085 Fax PWB part information
• 681217 Power supply unit 2 / directions flaw in REP 1.3
February 2009
The WorkCentre 4250 has been introduced. This is a variation of the WorkCentre 4260.
Throughout this manual, procedures and parts that are unique to either the WorkCentre 4150
family, the WorkCentre 4250 family or the WorkCentre 4260 family will be designated 4150,
4250 or 4260.
The following procedures are updated:
• 01-100 Side Cover Assembly Open RAP
• 01A Power Failure RAP
• 03A Unable to Boot RAP
• 06-100, 200 LSU Error RAP
• 07-120 Tray 1 Cassette Out RAP
• 07-130 Jam 0 From Tray 1 RAP
• 07-230, 330, 430 Jam 0 From Tray 2, 3, 4 or HCF RAP
• 07-530 Jam 0 From the Bypass Tray RAP
• 08-100 Jam 1 RAP
• 08-600 Duplex Jam 0 RAP