Parameter List
1
1.9 F: Options
YASKAWA TOEPYAIGA8002B GA800 Drive Programming 53
◆ F4: Analog Output Option
No.
(Hex.)
Name Description
Default
(Range)
Ref.
F4-01
(0391)
Terminal V1 Function
Selection
Sets the monitor signal output from terminal V1.
Set the x-xx part of the Ux-xx [Monitor]. For example, set F4-01 = 102 to monitor U1-02
[Output Frequency].
102
(000 - 999)
330
F4-02
(0392)
RUN
Terminal V1 Gain
Sets the gain of the monitor signal that is sent from terminal V1. Sets the analog signal
output level from the terminal V1 at 10 V or 20 mA as 100% when an output for
monitoring items is 100%.
100.0%
(-999.9 - +999.9%)
330
F4-03
(0393)
Terminal V2 Function
Selection
Sets the monitor signal output from terminal V2.
Set the x-xx part of the Ux-xx [Monitor]. For example, set F4-03 = 103 to monitor U1-03
[Output Current].
103
(000 - 999)
331
F4-04
(0394)
RUN
Terminal V2 Gain
Sets the gain of the monitor signal that is sent from terminal V2. Sets the analog signal
output level from terminal V2 at 10 V or 20 mA as 100% when an output for monitoring
items is 100%.
50.0%
(-999.9 - +999.9%)
331
F4-05
(0395)
RUN
Terminal V1 Bias
Sets the bias of the monitor signal that is sent from terminal V1. When an output for
monitoring items is 0%, this parameter sets the analog signal output level from the V1
terminal as a percentage of 10 V or 20 mA.
0.0%
(-999.9 - +999.9%)
331
F4-06
(0396)
RUN
Terminal V2 Bias
Sets the bias of the monitor signal that is sent from terminal V2. Set the level of the analog
signal sent from the V2 terminal at 10 V or 20 mA as 100% when an output for monitoring
items is 0%.
0.0%
(-999.9 - +999.9%)
331
F4-07
(0397)
Terminal V1 Signal Level
Sets the output signal level for terminal V1.
0 : 0 to 10 V
1 : -10 to 10 V
0
(0, 1)
332
F4-08
(0398)
Terminal V2 Signal Level
Sets the output signal level for terminal V2.
0 : 0 to 10 V
1 : -10 to 10 V
0
(0, 1)
332
◆ F5: Digital Output Option
No.
(Hex.)
Name Description
Default
(Range)
Ref.
F5-01
(0399)
Terminal P1-PC Function
Select
Sets the function of terminal P1-PC on the DO-A3 option. Set F5-09 = 2 [DO-A3 Output
Mode Selection = Programmable (F5-01 to F5-08)] to enable this function.
0
(0 - 1A7)
333
F5-02
(039A)
Terminal P2-PC Function
Select
Sets the function of terminal P2-PC on the DO-A3 option. Set F5-09 = 2 [DO-A3 Output
Mode Selection = Programmable (F5-01 to F5-08)] to enable this function.
1
(0 - 1A7)
333
F5-03
(039B)
Terminal P3-PC Function
Select
Sets the function of terminal P3-PC on the DO-A3 option. Set F5-09 = 2 [DO-A3 Output
Mode Selection = Programmable (F5-01 to F5-08)] to enable this function.
2
(0 - 1A7)
334
F5-04
(039C)
Terminal P4-PC Function
Select
Sets the function of terminal P4-PC on the DO-A3 option. Set F5-09 = 2 [DO-A3 Output
Mode Selection = Programmable (F5-01 to F5-08)] to enable this function.
4
(0 - 1A7)
334
F5-05
(039D)
Terminal P5-PC Function
Select
Sets the function of terminal P5-PC on the DO-A3 option. Set F5-09 = 2 [DO-A3 Output
Mode Selection = Programmable (F5-01 to F5-08)] to enable this function.
6
(0 - 1A7)
334
F5-06
(039E)
Terminal P6-PC Function
Select
Sets the function of terminal P6-PC on the DO-A3 option. Set F5-09 = 2 [DO-A3 Output
Mode Selection = Programmable (F5-01 to F5-08)] to enable this function.
37
(0 - 1A7)
334
F5-07
(039F)
Terminal M1-M2
Function Select
Sets the function of terminal M3-M2 on the DO-A3 option. Set F5-09 = 2 [DO-A3 Output
Mode Selection = Programmable (F5-01 to F5-08)] to enable this function.
F
(0 - 1A7)
334
To Next Page
Loading...
