YASKAWA GA800

YASKAWA TOEPYAIGA8002B GA800 Drive Programming 637
Index
Numerics
24 V power supply
Power supply input terminals ..................................... 626
A
Acceleration and deceleration times
Switching by external input ....................................... 247
Switching by output frequency ................................... 248
Switcing by Motor 2 Selection commands...................... 248
Acceleration time
Parameter ............................................................ 247
Unit of measurement setting ...................................... 250
Adjustment of control functionality .................................. 600
AFR
Parameter ............................................................ 486
ALM indicator..................................................... 543, 546
ALM/ERR
LED status........................................................... 549
Ambient Temperature Setting
Parameter ............................................................ 478
Analog gauge
Monitors ............................................................. 557
Analog input
Function selection for terminals A1 through A3 ............... 405
Analog Output
Gain/Bias Adjustment ............................................. 419
Monitor Parameter Selection...................................... 419
Signal Level Selection ............................................. 419
Terminal AM Monitor Selection ................................. 421
Terminal FM Monitor Selection .................................. 420
Application Preset....................................................... 179
ASR
Closed Loop V/f Control adjustment procedure ............... 261
Fine tuning .......................................................... 263
Parameter ............................................................ 260
Vector Control Adjustment Procedure........................... 261
ASR tuning............................................................... 593
Precautions .......................................................... 597
Auto-Tuning ............................................................. 589
ASR and Inertia Tuning Parameters ............................. 538
ASR tuning .......................................................... 593
Induction Motor .................................................... 589
Induction Motor Parameters ...................................... 532
Inertia Tuning ....................................................... 593
PM Motor Parameters.............................................. 535
PM Motors .......................................................... 590
Precautions .......................................................... 595
Precautions to Note before ASR Tuning ........................ 597
Precautions to Note before Inertia Tuning ...................... 597
Procedure ............................................................ 574
Rotational Auto-Tuning Precautions............................. 596
Stationary Auto-Tuning for Line-to-Line Resistance
precautions.................................................... 597
Stationary Auto-Tuning Precautions............................. 596
Stator resistance Auto-Tuning precautions...................... 597
B
Backlight
Timing of shut-off .................................................. 585
Backup
Parameters (drive to keypad) ..................................... 566
Backup function ......................................................... 522
Bar graph
Monitors ............................................................. 555
Base frequency
Parameter ............................................................ 302
Base Frequency
Motor 2 Parameters ................................................ 307
Base voltage
Motor 2 parameters................................................. 308
Parameter ............................................................ 303
Bi-Directional function ................................................. 287
Braking Resistor
Protective function ................................................. 475
bUS
Detection condition settings....................................... 345
Detection conditions ............................................... 341
Operation Selection after Detection.............................. 340
C
Capacitor Maintenance Setting........................................ 524
Carrier frequency
Diminish ............................................................. 480
Parameter ............................................................ 269
CE
Detection Selection................................................. 424
Detection Time...................................................... 424
Operation Selection after Detection.............................. 423
Checklist
Test run .............................................................. 607
Communication option
Parameter ............................................................ 335
Connecting multiple drives ............................................ 336
Control circuit terminals
Configuration of terminal block .................................. 626
I/O terminals function selection switches ....................... 631
Terminal functions ................................................. 624
Wire gauge .......................................................... 627
Wiring................................................................ 623
Wiring procedure for terminal block............................. 628
Control method
Selection ............................................................. 176
Cooling Fan
Activation Conditions Setting .................................... 477
Off Delay Timer .................................................... 478
Crimp ferrule ............................................................ 627
Cumulative Operation TimeSetting................................... 523
Current Detection Speed Search ...................................... 211
D
Data log................................................................... 583
Monitor selection ................................................... 583
Sampling time....................................................... 584
Start procedure...................................................... 582
Stop procedure ...................................................... 582
DC Injection Braking
Parameter ............................................................ 207
Deceleration time
Parameter ............................................................ 247
Unit of measurement setting ...................................... 250
Delete
Delete Backed-up Parameters..................................... 569
Derating
Ambient Temperature Setting..................................... 478