YASKAWA GA800

Parameter List
1
1.22 Parameters Changed by PM Motor Code Selection
YASKAWA TOEPYAIGA8002B GA800 Drive Programming 151
1.22 Parameters Changed by PM Motor Code Selection
Note:
The motor codes listed in these tables are the only correct setting values.
◆ Yaskawa SMRA Series SPM Motors
Table 1.4 SMRA series motor code setting for specification of 200 V at 1800 min
-1
(r/min)
No. Name Unit Motor Code (setting value of E5-01)
E5-01
PM Motor Code Selection - 0002 0003 0005 0006 0008
Voltage Class V 200 200 200 200 200
Capacity kW 0.4 0.75 1.5 2.2 3.7
Motor Rotation Speed min
-1
1800 1800 1800 1800 1800
E5-02 PM Motor Rated Power kW 0.4 0.75 1.5 2.2 3.7
E5-03
PM Motor Rated Current
(FLA)
A 2.1 4.0 6.9 10.8 17.4
E5-04 PM Motor Pole Count - 8 8 8 8 8
E5-05
PM Motor Resistance (ohms/
phase)
Ω 2.47 1.02 0.679 0.291 0.169
E5-06
PM d-axis Inductance (mH/
phase)
mH 12.7 4.8 3.9 3.6 2.5
E5-07
PM q-axis Inductance (mH/
phase)
mH 12.7 4.8 3.9 3.6 2.5
E5-09
PM Back-EMF Vpeak (mV/
(rad/s))
mVs/rad 0 0 0 0 0
E5-24
PM Back-EMF L-L Vrms
(mV/rpm)
mV/min
-1
62.0 64.1 73.4 69.6 72.2
E1-04 Maximum Output Frequency Hz 120 120 120 120 120
E1-05 Maximum Output Voltage V 200.0 200.0 200.0 200.0 200.0
E1-06 Base Frequency Hz 120 120 120 120 120
E1-09 Minimum Output Frequency Hz 6 6 6 6 6
C5-17 Motor Inertia kgm
2
0.0007 0.0014 0.0021 0.0032 0.0046
L3-24
Motor Accel Time @ Rated
Torque
s 0.064 0.066 0.049 0.051 0.044
n5-02
Motor Inertia Acceleration
Time
s 0.064 0.066 0.049 0.051 0.044
n8-49 Heavy Load Id Current % 0 0 0 0 0
Table 1.5 SMRA Series Motor Code Setting for Specification of 200 V at 3600 min
-1
(r/min)
No. Name Unit Motor Code (setting value of E5-01)
E5-01
PM Motor Code Selection - 0103 0105 0106 0108
Voltage Class V 200 200 200 200
Capacity kW 0.75 1.5 2.2 3.7
Motor Rotation Speed min
-1
3600 3600 3600 3600
E5-02 PM Motor Rated Power kW 0.75 1.5 2.2 3.7
E5-03
PM Motor Rated Current
(FLA)
A 4.1 8.0 10.5 16.5
E5-04 PM Motor Pole Count - 8 8 8 8
E5-05
PM Motor Resistance (ohms/
phase)
Ω 0.538 0.20 0.15 0.097
E5-06
PM d-axis Inductance (mH/
phase)
mH 3.2 1.3 1.1 1.1
E5-07
PM q-axis Inductance (mH/
phase)
mH 3.2 1.3 1.1 1.1