Agilent Technologies PNA Series User Manual

Index-10 Service Guide E8361-90001
Index
test port output power
accuracy
, 3-28
test port output power
linearity
, 3-29
trace noise
, 3-30
verification
ANSI/NCSL Z540-1-1994
, 3-8
non-ANSI/NCSL Z540-1-1994
,
3-9
phase lock board
illustrated, 6-13, 6-15
operation
, 5-10
part number
, 6-12, 6-14
removal and replacement
illustrated
, 7-21
procedure
, 7-20
test nodes
, 4-37
phase lock receiver board
removal and replacement
illustrated
, 7-25
procedure
, 7-24
phase stability check
failure of, 3-16
test port cables
, 3-15
pin assignments
connectors
AUX I/O
, 5-15
HANDLER I/O
, 5-14
TEST SET I/O
, 5-13
ping
command, LAN, 4-24
from network
, 4-25
to analyzer
, 4-24
pixel
damaged, 4-19
definition
, 4-19
PMYO (permanent-magnet YIG
oscillator)
frequency adjustment, 3-51
theory of operation
, 5-10
Port 1
check, 3-10
typical power output
, 4-49
Port 2
check, 3-10
typical power output
, 4-50
post-repair procedures , 7-66
power meter accuracy test , 3-36
power supply
check, 4-7
functional description of
, 5-5
functional group
, 5-3
if all voltages are missing
, 4-10
operation
, 5-29
voltage checks
, 4-8
power supply assembly
illustrated, 6-13, 6-15
part number
, 6-12, 6-14
removal and replacement
illustrated
, 7-17
procedure
, 7-16
troubleshooting
, 4-7
power, source
accuracy test, 3-28
linearity test
, 3-29
power, test port output
accuracy test, 3-28
linearity test
, 3-29
pre-repair
procedures, 7-3
caution about
, 7-3
warnings about
, 7-3
preventive maintenance
effect on error terms, A-3
printed service guide,
Option 0BW , 2-5
probe power
connector, 5-26
measurement points
, 4-7
troubleshooting
, 4-17
processing subgroup
operation, 5-27
protection
against ESD, 1-5, 3-4, 4-3, 7-3,
A-4
protective end caps
for connectors
part numbers
, 6-38
R
R1 channel
troubleshooting, 4-30
R1 receiver module
troubleshooting, 4-53
R1 trace
troubleshooting, 4-30, 4-33
R2 channel
troubleshooting, 4-30
R2 receiver module
troubleshooting, 4-53
R2 trace
troubleshooting, 4-30, 4-33
rack mount kits
part numbers, 6-40
with handles, Option 1CP
, 2-5
without handles, Option 1CM
,
2-5
raising the receiver deck
illustrated, 7-9
procedure
, 7-8
RAM, main
operation, 5-27
rear panel
connectors
1284-C
, 5-28
AUX I/O
, 5-12
Display
, 5-28
EXT 10 MHz REF IN
, 5-10
GPIB
, 5-28
HANDLER I/O
, 5-12
LAN
, 5-28
PARALLEL
, 5-28
RS-232
, 5-28
SERIAL
, 5-28
TEST SET I/O
, 5-12
TRIG IN
, 5-12
TRIG OUT
, 5-12
USB
, 5-28
VGA
, 5-28
interconnects
, 5-10, 5-12, 5-28
replaceable parts
illustrated
, 6-37
part numbers
, 6-37
troubleshooting
, 4-21
rebuilt-exchange assemblies
program, 6-5
receiver
accuracy
dynamic accuracy test
, 3-34
calibration
, 3-44
compression test
, 3-30
dynamic accuracy test
, 3-34
functional description of
, 5-4
functional group
, 5-3
linearity
dynamic accuracy test
, 3-34
output
troubleshooting
, 4-53
receiver (A13)
output
troubleshooting
, 4-57
receiver deck
raising and removing
illustrated
, 7-9
procedure
, 7-8
receiver display
running the test, 4-30
receiver group
block diagram, 5-21
defined
, 4-31, 4-32
operation
, 5-20
troubleshooting
, 4-52
receiver module
channel A
illustrated
, 6-21
operation
, 5-20
part number
, 6-20
removal and replacement
illustrated
, 7-51
removal and replacement
procedure
, 7-50
channel B
illustrated
, 6-21
operation
, 5-20

Agilent Technologies PNA Series Specifications

General

Brand	Agilent Technologies
Model	PNA Series
Category	Measuring Instruments
Language	English