Allen-Bradley MicroLogix 1100

To Next Page

To Previous Page

Publication 1763-UM001E-EN-P - June 2015

104 Using the LCD

Operating Buttons

Using Menus to Choose Values

Button Function

Cursor

Buttons

Move cursor

Select menu item

Choose file numbers, values, etc.

OK Next menu level, store your entry, apply the

changes

ESC Previous menu level, cancel your entry

Press To

• Go to next menu level.

• Store your entry.

• Apply the changes.

• Go to previous menu level.

• Cancel your entry since the last Ok.

• Press repeatedly to go to the main menu.

• Change menu item.

• Change value.

• Change position.

ESC OK

ESC

Main Page

Default Chapter3
- Default Chapter3
  - Firmware Revision History3
  - Table of Contents5
- Preface11
Chapter 113
- Hardware Features13
Hardware Overview13
- Component Descriptions14
  - Micrologix 1100 Memory Module and Built-In Real-Time Clock14
  - 1762 Expansion I/O15
- Communication Cables16
- Communication Options18
- Programming18
- Agency Certifications21
Chapter 221
- Compliance to European Union Directives21
  - EMC Directive22
  - Low Voltage Directive22
Installing Your Controller21
- Installation Considerations22
- Safety Considerations23
- Power Considerations26
- Preventing Excessive Heat27
- Master Control Relay28
- Installing a Memory Module32
- Using the Battery33
  - Connecting the Battery Wire Connector34
- Controller and Expansion I/O Spacing35
- Controller Mounting Dimensions35
- Mounting the Controller36
- 1762 Expansion I/O Dimensions39
- Mounting 1762 Expansion I/O39
  - DIN Rail Mounting39
  - Panel Mounting40
- Connecting Expansion I/O41
Chapter 3 Wiring Requirements43
- Wiring Recommendation43
- Wiring the Terminal Block44
Wiring Your Controller43
- Using Surge Suppressors45
  - Recommended Surge Suppressors47
- Grounding the Controller48
- Wiring Diagrams49
  - Terminal Block Layouts49
  - Terminal Groupings51
- Sinking and Sourcing Wiring Diagrams52
  - 1763-L16AWA, 1763-L16BWA, 1763-L16BBB and 1763-L16DWD52
  - Wiring Diagrams52
- Controller I/O Wiring55
  - Minimizing Electrical Noise55
- Wiring Your Analog Channels55
- Expansion I/O Wiring58
  - Digital Wiring Diagrams58
  - Analog Wiring65
Chapter 473
Communication Connections73
- Supported Communication Protocols73
- Default Communication Configuration74
- Using the Communications Toggle Functionality74
  - Changing Communication Configuration75
- Connecting to the RS-232 Port78
- Connecting to a DH-485 Network85
- Connecting the AIC91
- Connecting to Ethernet99
  - Ethernet Connections99
Using the LCD101
Chapter 5 Using the LCD Operating Principles102
- Startup Screen103
- Main Menu and Default Screen104
- Operating Buttons106
- Using Menus to Choose Values106
- Selecting between Menu Items107
- Cursor Display107
- Setting Values108
- Operating Principles102
- I/O Status109
  - Viewing I/O Status110
- Monitoring Bit File111
  - Target Bit File Number (TBF)111
  - Monitoring a Bit File113
- Monitoring Integer File117
  - Target Integer File Number (TIF)117
  - Monitoring an Integer File119
- Using the Mode Switch124
  - Controller Modes124
  - Changing Mode Switch Position125
- Using a User Defined LCD Screen128
  - User Defined LCD Screen128
- Changing Key in Mode130
  - Key in Modes130
  - Changing Key in Mode131
- Configuring Advanced Settings130
- Using Communications Toggle Functionality133
- Viewing Ethernet Port Configuration133
- Using Trim Pots135
  - Trim Pot Operation135
  - Changing Data Value of a Trim Pot135
  - Trim Pot Configuration in LCD Function File137
  - Error Conditions137
- Viewing System Information138
- Publication 1763-UM001E-EN-P - June139
- Viewing Fault Code139
Chapter 6141
- Operation at Power-Up and Entering a Run or141
- Test Mode141
- Writing Data to the Real-Time Clock142
- RTC Battery Operation142
- Real-Time Clock Operation141
- Memory Module Operation143
Chapter 7 Overview of Online Editing147
- Online Editing Terms148
- Effects of Online Editing on Your System149
- Directions and Cautions for Micrologix 1100 Online150
- Edit User150
- Types of Online Editing153
  - Edit Functions in Runtime Online Editing154
  - Edit Functions in Program Online Editing154
Appendix A Expansion I/O Specifications165
- Digital I/O Modules165
- Analog Modules173
Appendix B181
- Micrologix 1100 Replacement Kits181
- Lithium Battery (1763-BA)182
Appendix C187
- Controller Status LED Indicators187
- Status Indicators on the LCD188
- I/O Status Indicators on the LCD189
- Normal Operation190
- Error Conditions190
- Understanding the Controller Indicator Status187
- Controller Error Recovery Model191
- Analog Expansion I/O Diagnostics and Troubleshooting192
- Calling Rockwell Automation for Assistance196
Appendix D Preparing for Upgrade197
- Install Controlflash Software197
- Prepare the Controller for Updating198
- Sequence of Operation198
- Missing/Corrupt os LED Pattern199
Appendix E201
- Communication Interface201
- DF1 Full-Duplex Protocol201
- DF1 Half-Duplex Protocol203
- Communication Protocol207
- Ascii214
- Modbus Communication Protocol214
- Micrologix 1100 Controllers and Ethernet Communication215
- Publication 1763-UM001E-EN-P - June215
Appendix F216
- Micrologix 1100 Performance Considerations216
- Micrologix 1100 and PC Connections to the Ethernet Network218
- Ethernet Connections221
- Duplicate IP Address Detection222
- Configuring the Ethernet Channel on the Micrologix 1100223
- Configuration Using Rslogix 500 Programming Software224
- Configuration Via BOOTP224
  - Using the Rockwell BOOTP/DHCP Utility226
- Using a DHCP Server to Configure Your Processor228
- Using Subnet Masks and Gateways228
  - Manually Configuring Channel 1 for Controllers on Subnets230
- Micrologix 1100 Embedded Web Server Capability231
- System Loading Calculations233
Appendix G System Loading Example Calculations234
- System Loading Worksheet236
  - Current Loading236
- Calculating Heat Dissipation238
Glossary239

Table of Contents

Other manuals for Allen-Bradley MicroLogix 1100

Related product manuals