EasyManuals Logo

AVL F-FEM-CON User Manual

Default Icon
110 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #105 background imageLoading...
Page #105 background image
105
Glossary and Abbreviations
F-FEM-CON — Users Guide
7 Glossary and Abbreviations
AB-encoder
A speed encoder with 2 tracks (A and B), which are in quadrature.
ADC
Analog Digital Converter.
Converts proportional analog quantities into digital numbers.
Add-on
A name for the F-FEM-DIO. It has no IEEE1349 network connection but must be
connected to an F-FEM-DAC, F-FEM-CNT or F-FEM-CON using the add-on
interface.
Antialiasing Filter
In principle, every sampling system requires an analog input filter, to attenuate
lower frequencies, called aliasing.
Basis-FEM-AIN
Basis-Front End Module-Analog In with bayonet locking
Cluster
Interconnection of several front end modules, which are connected with the
same ground strap.
DAC
Digital Analog Converter.
Converts digital numbers into proportional analog quantities.
DI
Digital input
DMS
Dehnmesstreifen, German abbreviation usually used for load cell
DO
Digital output
EMCON
Engine Monitoring and Control.
F-FEM
Acronym for Fast-Front End Module.
These include all FEM, that belong to the IEEE1394 family.
F-FEM-AIF
Fast-Front End Module-Analog In Fast with bayonet locking
F-FEM-AIN
Fast-Front End Module-Analog In with bayonet locking
F-FEM-AIS
Fast-Front End Module-Analog In Isolated with bayonet locking
F-FEM-CAIN
Fast-Front End Module-Classic Analog In with screw-type locking
F-FEM-CAIS
Fast-Front End Module-Classic Analog In Isolated with screw-type locking
F-FEM-CNT
Fast-Front End Module-Counter Input
F-FEM-CON
Fast-Front End Module-Controller
F-FEM-DAC
Fast-Front End Module-Digital Analog Converter
F-FEM-DIO
Fast-Front End Module-Digital In Out
F-FEM number
Number used to distinguish the modules (please refer to the F-FEM Paramete-
rization manual, Secondary literature on page 13).
FEM Classic
Generation preceding the F-FEM.
FEM-P
Classic Front End Module-Pressure In with screw-type locking.
FOL converter
If fiber optic link (FOL) converter are employed, the 5 V switch must be switched
to ON. This activates the power supply for the FOL converter.
Hall pickup
This is a speed encoders with the following characteristics: Its resistance
changes with the magnetic flux density. Using a permanent magnet and a
toothed wheel, it is possible to detect angles and thus measure speed. It is
usually available as a two-track encoder.
Heidenhain
Manufacturer of incremental encoders.
IEEE1394
High-speed bus for linking F-FEM modules. Baud rates of 100, 200 or 400 Mbps
are possible. Supports the sychronism of a distributed system by using an
isochronous protocol.
Inductive pick-up
Using a permanent magnet, an inductive pick-up generates a voltage in a coil
over an alternating air gap (toothed wheel). This voltage can be evaluated as
angle pulse or speed. It is usually available as a single-track encoder.
Integral
Non-linearity
The integral non-linearity expresses the deviation from the ideal transfer function
relative to the full scale range of the ADC. The ideal transfer function is a line

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the AVL F-FEM-CON and is the answer not in the manual?

AVL F-FEM-CON Specifications

General IconGeneral
BrandAVL
ModelF-FEM-CON
CategoryMeasuring Instruments
LanguageEnglish

Related product manuals