1. Safety
To prevent personal injury
• Isolate electrically before replacing the lamp or lamp house. Caution: Hot lamp (house ).
• Caution: High pressure lam p may explode if impro perly handled. Refer servicing to qualified se rvice personnel.
• To prevent injury and physical damage, always read this manual and all labels on the system before inserting the lamp casing,
powering the projector or adjusting the projector.
• To prevent injury, take note of the weight of the projector. Minimum 4 persons are needed to carry the projector.
• To prevent injury, ensure that the lens, exhausting system and all cover plates are correctly installed. See installation proce-
dures.
• Warning: high intensity light beam. NEV ER look into the lens ! High luminance c ould result in damage to the eye.
• Before attempting to r emove any of the projector’s covers, disconnect to the projector mains terminals and unplug the power
cord at UPS INLET for removal of all power from the projector.
• When re quired to remove all power from the projector, to access parts inside, always disc onnect t o the projector mains terminals
and unplug the power cord at UPS INLET
• Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious da mage to it and
possible injury to the user.
• It is haz ardous to op erate without lens or shield. Lenses, shields or ultra violet screens shall b e changed if they hav e become
visibly damaged to suc h an extent that their effectiveness is impaired. Fo r example by cracks or deep scratches.
• Warning: Protection from ultraviolet radiation: Do not look directly in the light beam . The lamp contained in this product is
an intense source of light and heat. One component of the light emitted from this lam p is ultraviolet light. P otential eye and s kin
hazards are present when the lamp is ener gized due to ultraviolet radiation. Avoid unneces sary exposure. Protect yourself and
your employ ees by ma king them aware of the hazards and how to protect t hemselves. P rotecting the skin can be accom plished
by wearing tightly wov en garm ents and glov es. Protecting the eyes from UV can be ac complished by wea ring safety glasses
that are designed to provide UV pro tection. In addition to the UV, the visible light from the lamp is intense and should also be
considered w hen choosing protective eye wear.
• Exposure to UV radiation: Some medications are k nown t o m ake individuals ex tra sens itive to UV radiation. T he A mer ican
Conference of Governmental Industrial Hygienists (ACGIH) recommends o ccupational UV exposure for an-8 hour d ay to be
less than 0,1 micro-watts per square centimeters of effective UV radiation. An evaluation of the workplace is advised to assure
employees are not expos ed to c umulative radiation levels exceeding these government guidelines.
WARNING: Never lo ok into the exhaust output. High luminance and UV radiation could result in dam age to
the eye. The installation of an exh aust system is mandatory before oper
ating the projector.
To prevent fire hazard
• Do not place flamma ble o r com bustible m aterials ne ar the projector!
• Barco large screen projection products are designed and manufactured to meet the most stringent safety regulations. This
projector radiates heat on its external surfaces and from ventilation ducts during normal operation, which is both nor mal and
safe. Exposing flammable or combustible materials into close proximity of this projector could result in the spontaneous ignition
of that material, resulting in a fire. For this reason, it is absolutely necessary to leave an “exclusion zone” arou nd all external
surfaces of the projector whereby no flam mable o r combustible m aterials are present. The exclusion zon e mu st be not less
than 40 c m (16”) for all DLP Cinema projectors. The exclusion zone on the lens side mu st be at least 5 m. Do not cover the
projector or the lens with any material while the projector is in operation. Keep flammab le a nd combustible m aterials away from
the projector at all times. Mount the projector in a well ventilated area away from sources of ignition and out of direct s un light.
Never expose the pr ojector to rain or moisture. In the event of fire, use sand, CO
2
or dry powder fire extinguishers. Nev er us e
water on an electrical fire. Always have service performed on this projector by authorized B arco ser vice personnel. Always
insist o n gen uine Barco replacement parts. Never use non-Barco replacement parts as they may degrade the s afety of this
projector.
• Slots and openings in this equipment are provided for ventilation. To ensure reliable oper ation of the projector an d to protect
it from overheating, these openings must not be blocked or covered. The ope nings should never be blocked by placing the
projector too close to walls, or other similar surface. This projector should never be placed near or over a radiator or heat
register. Th is p rojector should not be placed in a built-in installation or enclosure unless p roper ventilation is provided.
• Projection rooms must be well ven
tilated or cooled in order to avoid build up of heat. It is necessary to vent hot e xhaust air from
console to the outside of the building. The mandatory exhaust sy stem mu st include a blower that m aintain at least 1 0 m
3
/min
(350 CFM ) when measured at the projector exhaust opening.
• Let the projector cool c ompletely before storing. Remove cord from the projector when storing.
• Heat s ensitive materials should not be p laced in the path of the exhausted air or on the lamp house.
6
R59770495 DP2K-23B 30/04/2010
To Next Page
Loading...
Need help?
General
Weight and Dimensions
