Bosch D9412GV2 - Routing; Called Party Disconnect; Route Number Groups: Which Has the Highest Priority; Programming Primary and Backup Destinations

D9412GV2/D7412GV2 | Program Entry Guide | 2.0 GV2MAIN EN | 13
Bosch Security Systems | 5/05 | F001U003636B
Expand Test Rpt
Default: No
Selection:
Yes or No
Yes Off-normal events listed in Routing
Group Test Reports are reported to
the central station.
No Off-normal conditions for the events
listed in the Routing Group Test
Reports at test time are not reported.
Use this program item to add system event
information to scheduled Test Reports. Refer to Section
5.2 Skeds on page 108.
This parameter relates to Sked Function
Code 9 (Test Report) because it allows a
Sked to send Expanded Test Report
information. Expand Test Rpt does not
affect Sked Function Codes 28 (Expanded
Off-Normal Test Report) and 29 (Non-
Expanded Off-Normal Test Report).
2.3 Routing
Use routing to select full or partial groups of events
that report to up to four different destinations. Routing
includes choosing the most important destination
(route number), reporting the events to a single or
multiple destination, and selecting a backup
destination if the events fail.
2.3.1 Called Party Disconnect
Telephone companies provide called party disconnect
to allow the called party to terminate a call. The called
party must go on hook (hang up) for a fixed interval
before a dial tone is available for a new call. This
interval varies with telephone company equipment.
D9412GV2/D7412GV2 firmware allows for called
party disconnect by adding a 35-second on-hook
interval to the dial-tone detect function. If the control
panel does not detect a dial tone in seven seconds, it
puts the phone line on hook for 35 seconds to activate
called party disconnect. The phone line goes off hook
and begins a seven-second dial tone detect. If no dial
tone is detected, the control panel dials the number
anyway. Each time the number is dialed, the control
panel records this as an attempt. After ten attempts,
the control panel enters communications failure and
Comm Fail Route # appears on the keypads.
2.3.2 Route Number Groups: Which Has the
Highest Priority?
To program a group, first choose a route number. The
lower the route number, the higher priority that group
has (for example, events reported for Route 1 have a
higher priority than Routes 2, 3, or 4 if each group
tries to send a message at the same time). The priority
of the route numbers becomes important when
programming duplicate reports or choosing the events
you want to report first regardless of the number of
events that must report to multiple groups. Route 1
group primary device is the first destination the control
panel attempts to dial if an event in that group must be
reported. If the control panel is idle, any event
generated for any group starts a dialing sequence.
2.3.3 Programming Primary and Backup
Destinations
Each route number has an
R# Primary Device and
an
R# Backup Device . In typical applications where
two phone numbers are programmed, the
R# Primary
Device
destination is the phone number that the route
group attempts to dial first. If the
R# Primary Device
destination does not connect to the central station
receiver after two dialing attempts, the control panel
dials the
R# Backup Device destination.
You can also program the control panel so that the
R# Primary Device or the R# Backup Device uses
an SDI device, such as a D4020 Network Interface
Module. You can program the control panel to make
only one attempt for the
R# Primary Device before
attempting to send events using the
R# Backup
Device
.
2.3.4 Enhanced Routing
The D9412GV2 and D7412GV2 allow events to be
sent to up to four additional SDI Paths. The network
interface module (NIM) connects directly to the SDI
Bus and occupies SDI Address 88. For additional
information regarding the specific programming
requirements for enhanced communications, refer to
Section 2.4 Enhanced Routing on page 21 and Section 6.5
Programming Path Numbers and IP Addresses for Enhanced
Communications on page 127.
2.3.5 Programming a Duplicate Report
Select Yes for each available route number to allow an
event within a group to send a report to multiple
groups. For instance, if fire alarms are programmed for
Route Group 1 and Route Group 2, a fire alarm sends
a report first to Route Group 1, followed by a
duplicate report to Route Group 2.