Canon imagePROGRAF iPF6400 User Manual

Cause Corrective Action
A cut line is printed because CutDustRe-
duct. is On in the Control Panel menu to re-
duce cutting dust.
If this function is not needed, set CutDustReduct. to Off in the Control Panel menu.
(See "Menu Settings.") →P.648
The Printhead is set too low in the Control
Panel menu.
In the Control Panel menu, set Head Height to Automatic.
(See "Troubleshooting Paper Abrasion and Blurry Images.") →P.735
You are printing on heavyweight paper or pa-
per that curls or wrinkles easily after absorb-
ing ink.
When printing on Canon Heavyweight Coated Paper or other paper-based media, choose a
VacuumStrngth setting of Strong or Strongest in the Control Panel menu. If rubbing still oc-
curs, in the Control Panel menu, use a higher Head Height setting.
(See "Adjusting the Vacuum Strength.") →P.744
(See "Troubleshooting Paper Abrasion and Blurry Images.") →P.735
When printing on CAD Tracing Paper or other film-based media, choose a VacuumStrngth
setting of Standard, Strong, or Strongest in the Control Panel menu. If rubbing still occurs, in
the Control Panel menu, use a higher Head Height setting.
(See "Adjusting the Vacuum Strength.") →P.744
(See "Troubleshooting Paper Abrasion and Blurry Images.") →P.735
The Ejection Guide is soiled. Clean the Ejection Guide.
(See "Cleaning the Printer Exterior.") →P.861
The surface of the paper is dirty
The surface of the paper is dirty
Cause Corrective Action
The Paper Retainer is soiled. Clean the Paper Retainer.
(See "Cleaning Inside the Top Cover.") →P.861
You are using a paper that does not
dry easily.
In the Control Panel menu, set Roll DryingTime to at least 1 min.
(See "Menu Settings.") →P.648
When paper that does not dry easily is used for printing, it may curl during printing and touch the Output
Tray.
In this case, in the Control Panel menu, complete the settings for Dry time and Area in Scan Wait
Time.
However, note that printing will now take longer.
(See "Menu Settings.") →P.648
The back side of the paper is dirty
The back side of the paper is dirty
Cause Corrective Action
The Platen has become dirty after borderless printing or printing on small pa-
per.
Open the Top Cover and clean the Platen.
(See "Cleaning Inside the Top Cover.") →P.861
The Platen suction is too strong. In the Control Panel menu, reduce the level of VacuumStrngth.
(See "Adjusting the Vacuum Strength.") →P.744
BordlessOversize is set to Standard in the Control Panel menu. Set BordlessOversize to Little in the Control Panel menu.
(See "Menu Settings.") →P.648
Roller marks are left across the trailing edge of paper
Roller marks are left across the trailing edge of paper
Cause Corrective Action
The paper was removed without pressing the OK button after
printing from the Front Paper Feed Slot.
Following the instructions displayed, press the OK button, and after remov-
ing the paper, press the OK button again.
Wipe the rollers to clean them.
(See "Cleaning Inside the Top Cover.") →P.861
(See "Cleaning the Paper Retainer.") →P.864
iPF6400
The surface of the paper is dirty
User's Guide
Troubleshooting Problems with the printing quality
893

Canon imagePROGRAF iPF6400 Specifications

General

Color	Yes
Printing colors	Black, Blue, Cyan, Green, Grey, Magenta, Matte black, Photo cyan, Photo grey, Photo magenta, Red, Yellow
Maximum resolution	2400 x 1200 DPI
Page description languages	GARO
Maximum print size	-
Maximum roll length	18 m
ISO A-series sizes (A0...A9)	A1, A2
ISO B-series sizes (B0...B9)	B2
Internal memory	384 MB
Sound pressure level (printing)	47 dB
Power supply	100 W
Power consumption (off)	5 W
Power consumption (standby)	6 W
Storage temperature (T-T)	15 - 30 °C
Operating relative humidity (H-H)	10 - 80 %
USB port	No
USB 2.0 ports quantity	0