Cisco 7962G Administration Guide

5-10
Cisco Unified IP Phone Administration Guide for Cisco Unified Communications Manager 7.1
OL-18913-01
Chapter 5 Configuring Features, Templates, Services, and Users
Telephony Features Available for the Cisco Unified IP Phone
Intercom Allows users to place and receive intercom calls
using programmable phone buttons. You can
configure intercom line buttons to:
• Directly dial a specific intercom extension.
• Initiate an intercom call and then prompt the
user to enter a valid intercom number.
Note If your user logs into the same phone on a
daily basis using their Cisco Extension
Mobility profile, assign the phone button
template that contains intercom
information to their profile, and assign the
phone as the default intercom device for
the intercom line.
Cisco Unified Communications Manager
Feature and Services Guide, “Intercom
chapter”
Join/Select Allows user to join two or more calls that are on
one line to create a conference call and remain on
the call.
For more information:
• See the “Configuring Softkey Templates”
section on page 5-20.
• Refer to Cisco Unified Communications
Manager System Guide, “Cisco Unified IP
Phones” chapter.
Join Across
Lines/Select
Allows users to apply the Join feature to calls that
are on multiple phone lines.
For more information:
• See the “Configuring Softkey Templates”
section on page 5-20
• Refer to Cisco Unified Communications
Manager System Guide, “Cisco Unified IP
Phones” chapter.
Line select If this feature is disabled (default), then the
ringing line is selected. When enabled, the primary
line is picked up even if a call is ringing on another
line. The User must manually select the other line.
Note This feature can also be enabled or
disabled for Extension Mobility.
For more information, refer to the option
“Always use prime line” in the following
chapters of Cisco Unified Communications
Manager Administration Guide:
• “Device Profile Configuration”
• “Common Phone Profile Configuration”
• “Cisco Unified IP Phone Configuration”
Line select for voice
messages
When disabled (default), pressing the Messages
button selects the line that has a voice message. If
more than one line has voice mail, then the first
available line is selected. When enabled, the
primary line is always used to retrieve voice
messages.
Note This feature can also be enabled or
disabled for Extension Mobility.
For more information, refer to the option
“Always use prime line for voice message” in
the following chapters of Cisco Unified
Communications Manager Administration
Guide:
• “Device Profile Configuration”
• “Common Phone Profile Configuration”
• “Cisco Unified IP Phone Configuration”
Table 5-1 Telephony Features for the Cisco Unified IP Phone (continued)
Feature Description Configuration Reference

Cisco 7962G Specifications

General

Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Case material	ABS
Product color	Black, Grey
Wall mountable	Yes
Bluetooth	No
Security algorithms	128-bit AES, 802.1x RADIUS
Networking standards	IEEE 802.1Q, IEEE 802.1p, IEEE 802.1x, IEEE 802.3af
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet LAN interface type	Fast Ethernet
Ethernet LAN (RJ-45) ports	2
Voice codecs	G.711, G.711a, G.722, G.729A, G.729ab, iLBC
Volume control	Digital
Display diagonal	5 \
Display resolution	320 x 222 pixels
Display number of colors	Monochrome
Caller ID	-
Lines quantity	- lines
Phonebook capacity	- entries
Storage temperature (T-T)	-10 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Number of handles included	1 pc(s)

Weight and Dimensions

Depth	203.2 mm
Width	266.7 mm
Height	152.4 mm
Weight	1600 g