D-Link DWS-3160-24TC - Page 834

DWS-3160 Series Gigabit Ethernet Unified Switch CLI Reference Guide
830
condition will use.
<int 0-65535> - Enter the custom destination Layer 4 port number used here. This
value must be between 0 and 65535.
protocol - Specifies the protocol to filter for a named IP ACL rule, identified by number. The
protocol number is a standard value assigned by IANA and is interpreted as an integer
from 1 to 255. You can use the protocol number or you Specifies a protocol keyword.
ip - Specifies that the protocol, used to filter for a named IP ACL rule, is IP.
icmp - Specifies that the protocol, used to filter for a named IP ACL rule, is ICMP.
igmp - Specifies that the protocol, used to filter for a named IP ACL rule, is IGMP.
tcp - Specifies that the protocol, used to filter for a named IP ACL rule, is TCP.
udp - Specifies that the protocol, used to filter for a named IP ACL rule, is UDP.
other - Specifies a custom protocol number to use in the named IP ACL rule.
<int 1-255> - Enter the custom protocol number, used to filter for a named IP ACL rule,
here. This value must be between 1 and 255.
service - Specifies the Service Type match condition for the named IP ACL rule.
ip_precedence - Specifies the IP precedence field in a packet that is defined as the high-
order three bits of the Service Type octet in the IP header.
<value 0-7> - Enter the IP precedence value used here. This value must be between 0 and
7.
ip_tos - Specifies the IP ToS field in a packet that is defined as all eight bits of the Service
Type octet in the IP header. The ToS Bits value is a two-digit hexadecimal number from 00
to ff. The TOS Mask value is a two-digit hexadecimal number from 0x00 to 0xff,
representing an inverted mask. The zero-valued bits in the ToS Mask denote the bit
positions in the ToS bits value that are used for comparison against the IP ToS field of a
packet.
tos_bit - Specifies the ToS Bit value.
<hex 0x00-0xff> - Enter the ToS Bit value used here. This value must be between 0x00
and 0xff.
tos_mask - Specifies the ToS Mask value.
<hex 0x00-0xff> - Enter the ToS Mask value used here. This value must be between
0x00 and 0xff.
ip_dscp - Specifies the IP DiffServ Code Point (DSCP) field. The DSCP is defined as the
high-order six bits of the Service Type octet in the IP header. The IP DSCP is configured
by a possible selection of one of the DSCP keywords or a numerical values.
af11 - Specifies that the IP DiffServ Code Point value will be set as 'af11'.
af12 - Specifies that the IP DiffServ Code Point value will be set as 'af12'.
af13 - Specifies that the IP DiffServ Code Point value will be set as 'af13'.
af21 - Specifies that the IP DiffServ Code Point value will be set as 'af21'.
af22 - Specifies that the IP DiffServ Code Point value will be set as 'af22'.
af23 - Specifies that the IP DiffServ Code Point value will be set as 'af23'.
af31 - Specifies that the IP DiffServ Code Point value will be set as 'af31'.
af32 - Specifies that the IP DiffServ Code Point value will be set as 'af32'.
af33 - Specifies that the IP DiffServ Code Point value will be set as 'af33'.
af41 - Specifies that the IP DiffServ Code Point value will be set as 'af41'.
af42 - Specifies that the IP DiffServ Code Point value will be set as 'af42'.
af43 - Specifies that the IP DiffServ Code Point value will be set as 'af43'.
be - Specifies that the IP DiffServ Code Point value will be set as 'be'.
cs0 - Specifies that the IP DiffServ Code Point value will be set as 'cs0'.
cs1 - Specifies that the IP DiffServ Code Point value will be set as 'cs1'.
cs2 - Specifies that the IP DiffServ Code Point value will be set as 'cs2'.
cs3 - Specifies that the IP DiffServ Code Point value will be set as 'cs3'.
cs4 - Specifies that the IP DiffServ Code Point value will be set as 'cs4'.
cs5 - Specifies that the IP DiffServ Code Point value will be set as 'cs5'.
cs6 - Specifies that the IP DiffServ Code Point value will be set as 'cs6'.
cs7 - Specifies that the IP DiffServ Code Point value will be set as 'cs7'.
ef - Specifies that the IP DiffServ Code Point value will be set as 'ef'.
other - Specifies that a custom IP DiffServ Code Point value will be used.
<int 0-63> - Enter a custom IP DiffServ Code Point value here. This value must be
between 0 and 63.
del_rule - Specifies to delete a specified rule from a named IP ACL.