DIMA HC-200 - Page 154

To Next Page

To Previous Page

Appendix E HYBRID Coater Service Manual ver1.1

152

CONNECTOR P27 FOR ALIGNMENT SENSORS

This connector is not used at this moment.

CONNECTOR P28 FOR PUSH BUTTONS AND P29 FOR DOOR LOCKS

This connector is used to connect the push button on the front control panel of the machine.

Connector P29 is not used at this moment.

Main Page

Default Chapter3
- Table of Contents3
1 Introduction6
- About this Manual6
- Model Overview7
2 Safety8
- Warnings8
- Emergency Switches8
3 Machine Overview9
- Introduction9
- Electrical Block Diagram9
- Block Diagram of Air10
- Routing of the Air Lines11
- Air Lines Routing of the Options12
- With Options HC-1050 or HC-105112
- With Options HC-1000, HC-1010, or HC-103014
- With Options HC-1160/117016
- Electrical Compartment in Front17
- Electrical Compartment in Rear19
- Detection of Exhausted Air21
- And y Movement21
- Head with Connection PCB22
- Dispense Head PCB23
- Z Movement at23
- ZØ Movement at24
- Embedded Software25
- Additional Revision Information25
- General25
- Specific26
- HC-1160/ HC-1170 General26
- HC-1170 Specific26
4 Machine Installation27
- Pre-Installation Checks27
- Unpacking the Machine and Removing Transport Locks27
- Placing and Leveling the Machine29
- Connections and Pressure Setting29
- Completion of the Installation30
- Installing Special Options30
- Installing Options DD-52XX30
- Installing Option HC-1050/ HC-105130
- Installing Option HC-1210/ HC-121533
- Installing Option HC-1230/ HC-123133
- Installing Options HC-1235 and HC-123634
- Installing Option HC-132034
- Installing Options HC-1380 and HC-139036
- Installing Options HC-1160 and HC-117037
- Placing/Adjusting Stopper Pin/Product Detect Sensor of Conveyor37
- Adjusting the Conveyor Level and Height39
- Setting-Up the Weight Scales40
- Settings40
- Setting-Up the Com Parameters40
5 Maintenance43
- Introduction43
- Service Diagnostics43
- Regular Maintenance44
- Checklist for the Maintenance of the HYBRID48
6 Electrical Wiring52
- Electrical Wiring Diagrams52
- Overview of the Wiring Diagrams52
7 Pneumatics54
- Overview54
- Pneumatics Diagram54
8 Diagnostics for Pcb's57
- Introduction57
- Controller EL-0487357
- Led's on Upper Left Side of the EL-0487358
- Led's Near Connectors P1 and P2 on the EL-0487359
- Led's Near Connector P3 and P4 on the EL-0487360
- Led's on Upper Right Side of the EL-0487361
- Led's on Bottom Left Side of the EL-0487363
- Led's Near Connectors P21 Till P26 on the EL-0487364
- Led's Near Connectors P27 Till P29 on the EL-0487365
- Explanation of DIP-Switches on EL-0487366
- Advanced Power LED Controller EL-0487268
- Stepper Drivers EL-0487469
- Interconnection PCB EL-0487570
9 Small Repairs and Adjustments72
- Pressure Settings72
- Focusing the Fiducial Camera72
- Replacing the Fiducial Camera at a73
- Replacing the Fiducial Camera at a74
- Replacing Stepper Motors75
- Replacing the Stepper Motors of the X and y Axis75
- Replacing the Stepper Motor of the Z Axis on the76
- Replacing the Stepper Motor of the Ø Axis78
- Replacing Pcb's of Stepper Motors79
- Replacing and Adjusting the Encoder79
- Exchanging the Flexible Cable Duct on the82
- Adjusting the X, Y, Z and Ø Limits84
- Adjusting the Limits for the X Axis84
- Adjusting the Limits for the y Axis84
- Adjusting the Limits for the Z Axis with the84
- Adjusting the Limits for the Z Axis with the85
- Adjusting the Limits for the Ø Axis with the86
- Replacing the Differential Pressure Switch86
- Fitting a New Stop Pin in a Conveyor88
10 Spare Parts89
Electrical Wiring Diagrams Revision105
Electrical Wiring Diagrams Revision112
Electrical Wiring Diagrams of Options130
EL-04806 Dispense Head PCB Overview141
EL-04873 Control PCB Overview145
EL-04875 Connection PCB Overview157
EL-04876 Dispense Head PCB Overview163
EL-04879 Dispense Head PCB Overview167
I/O Assignment170

DIMA HC-200 - Page 154

Table of Contents

Related product manuals