Emerson Vilter MicroVission - Page 16

TOC − 10
MicroVission Controller • Operation and Service Manual • Emerson • 35391MV 1.3
Table / Figure Page Number
Table of Contents
Figure 5-5. Compressor Control Screen - Auto Cycle (Suction Pressure) with Pulldown Running ........... 5-6
Figure 5-6. Compressor Control Screen – Auto Cycle (Process Temperature) ........................................5-7
Figure 5-7. Compressor Control Screen – Auto Cycle (Process Temperature) with Pull Down Running .. 5-8
Figure 5-8. Compressor Control Screen - Auto Cycle (Discharge Pressure) ............................................5-9
Figure 5-9. Compressor Control Screen – Active Control Mode - I/O Based Setpoint Control .................5-10
Figure 5-10. Compressor Control Screen - Load Limiting ......................................................................5-11
Figure 5-11. Compressor Control Screen - Oil Control ..........................................................................5-12
Figure 5-12. Compressor Control Screen - VFD Settings Control ...........................................................5-13
Figure 5-13. Compressor Control Screen – Pumpdown Control ............................................................5-14
Figure 5-14. Compressor Control Screen – Pulldown Control
(Active Control Mode – Suction Pressure SP1) ......................................................................................5-16
Figure 5-15. Compressor Control Screen – Pulldown Control
(Active Control Mode – Process Control SP1) .......................................................................................5-17
Figure 6-1. Alarms and Trips Setpoints (Page 1) ....................................................................................6-2
Figure 6-2. Alarms and Trips Setpoints (Page 2) ....................................................................................6-3
Figure 6-3. Alarms and Trips Setpoints (Page 3) ....................................................................................6-3
Figure 6-4. Digital Inputs (Auxiliary I/O Screen) ....................................................................................6-13
Figure 6-5. Analog Inputs (Auxiliary I/O Screen) ...................................................................................6-16
Figure 6-6. Digital Result Variable Safety (Auxiliary I/O Screen) ............................................................6-21
Figure 6-7. Analog Result Variable Safety (Auxiliary I/O Screen)............................................................6-22
Figure 7-1. Timers Screen (Page 1) ....................................................................................................... 7-1
Figure 7-2. Timers Screen (Page 2) ....................................................................................................... 7-2
Figure 8-1. Instrument Calibration Screen Page 1 – Analog Inputs (Suction Pressure)...........................8-2
Figure 8-2. Instrument Calibration Screen Page 1 – Analog Inputs (Discharge Pressure) ....................... 8-2
Figure 8-3. Instrument Calibration Screen Page 1 – Analog Inputs (Oil Pressure) .................................. 8-3
Figure 8-4. Instrument Calibration Screen Page 1 – Analog Inputs (Filter In Pressure) ........................... 8-3
Figure 8-5. Instrument Calibration Screen Page 1 – Analog Inputs (Filter Out Pressure) ........................8-4
Figure 8-6. Instrument Calibration Screen Page 2 – Analog Inputs (Suction Temperature) ....................8-4
Figure 8-7. Instrument Calibration Screen Page 2 – Analog Inputs (Discharge Temperature) ................ 8-5
Figure 8-8. Instrument Calibration Screen Page 2 – Analog Inputs (Oil Temperature) ........................... 8-5
Figure 8-9. Instrument Calibration Screen Page 3 – Analog Inputs (Motor Current) ..............................8-6
Figure 8-10. Instrument Calibration Screen Page 3 – Analog Inputs (Process Temperature) ..................8-7
Figure 8-11. Instrument Calibration Screen Page 4 – Auxiliary Inputs ................................................... 8-8
Figure 8-12. Instrument Calibration Screen Page 5 – Auxiliary Inputs ................................................... 8-9
Figure 8-13. Instrument Calibration Screen Page 6 – Auxiliary Outputs ................................................ 8-10
Figure 8-14. Instrument Calibration Screen Page 6 – Auxiliary Outputs Disabled ..................................8-11
Figure 9-1. Event List Screen ................................................................................................................9-1
Figure 10-1. Input/Output States Screen Page 1 - Live I/O Data ............................................................10-1
Figure 10-2. Input/Output States Screen Page 2 - Live I/O Data ............................................................10-2
Figure 10-3. Input/Output States Screen Page 3 – Live I/O Data ...........................................................10-2
Figure 10-4. Input/Output States Screen Page 4 – Live I/O Data ...........................................................10-3
Figure 10-5. Input/Output States Screen Page 5 – Live I/O Data ...........................................................10-3
Figure 10-6. Input/Output States Screen Page 6 – Live I/O Data ...........................................................10-4
Figure 10-7. Input/Output States Screen - Freeze Data .........................................................................10-4
Figure 10-8. Input/Output States Screen – Freeze Data (Trip Condition) ...............................................10-5
Figure 11-1. User Access Screen - Login ................................................................................................11-1