Ericsson AVP 4000 - Page 39

Getting Started
1/1553-FGC 101 1790 Uen Y
3-3
3.13 How to Return to Default Settings from the GUI ................................ 3-95
3.14 Digital Programme Insertion (DPI) ..................................................... 3-95
3.14.1 Splice Point Operation ....................................................................... 3-95
3.14.2 SCTE104 over IP .............................................................................. 3-97
3.14.3 How to Configure Splicing ................................................................. 3-97
3.15 How to Control Temperature/Fan Speed ........................................... 3-98
3.16 How to Get and Apply Additional Licenses ........................................ 3-99
3.16.1 Verifying Which Licenses Are Present in the Unit .............................. 3-99
3.16.2 Video Licenses ................................................................................ 3-100
3.16.3 Ordering Additional Licenses ........................................................... 3-100
3.16.4 Entering License Keys ..................................................................... 3-101
3.17 Alarm Monitoring ............................................................................. 3-101
3.18 Simple Network Management Protocol ............................................ 3-102
3.18.1 Supported Protocols ........................................................................ 3-102
3.18.2 Operation ........................................................................................ 3-102
List of Figures
Figure 3.1 AVP 4000 Connections...................................................................... 3-7
Figure 3.2 Ethernet Control Port Numbering .................................................... 3-10
Figure 3.3 Ethernet Data Port Numbering ........................................................ 3-12
Figure 3.4 Configuring Basic Authentication ..................................................... 3-15
Figure 3.5 Configuring LDAP Authentication Test ............................................. 3-16
Figure 3.6 Configuring LDAP Authentication .................................................... 3-16
Figure 3.7 Service Configuration Web Page – Adding a Transport Stream ....... 3-18
Figure 3.8 Service Configuration Web Page – Adding a Service ......................
3-19
Fi
gure 3.9 Service Configuration Web Page – Adding a Component ................ 3-20
Figure 3.10 Adding Additional Output Services .................................................. 3-24
Figure 3.11 Viewing (Unsaved) Output Services (1 Linear and ABRs Shown) .... 3-25
Figure 3.12 Creating an ABR Service ................................................................. 3-26
Figure 3.13 Adding Additional Output Service .................................................... 3-27
Figure 3.14 Additional Output Service Added ..................................................... 3-28
Figure 3.15 Service Configuration Web Page – Turning Off Embedded PCR ..... 3-28
Figure 3.16 Service Configuration Web Page – Setting PCR PID ...................... 3-29
Figure 3.17 Service Configuration Web Page – Adding a Transport Stream ....... 3-30
Figure 3.18 Service Configuration Web Page – Adding a Service ...................... 3-30
Figure 3.19 Setting Transport Stream Mode to VBR (SPTS Multicast) ............... 3-31
Figure 3.20 Setting Transport Stream Mode to CBR (SPTS or MPTS
Multicast) ......................................................................................... 3-31
Figure 3.21 Setting Transport Stream Mode to VBR (SPTS Unicast) ................. 3-32
Figure 3.22 Setting Transport Stream Mode to CBR (SPTS or MPTS Unicast) .. 3-32
Figure 3.23 Service Configuration Web Page – Adding a Service ...................... 3-33
Figure 3.24 Service Configuration Web Page – Remux or Transcode ................ 3-33
Figure 3.25 Transcode Service Configuration – Adding a Service ...................... 3-34
Figure 3.26 Transcode Service Configuration – Component Selection ............... 3-34
Figure 3.27 Transcode Service Configuration – Bit Rate Selection .................... 3-35
Figure 3.28 Prompt for Monitor .......................................................................... 3-35
Figure 3.29 Configuring Jitter Tolerance ............................................................. 3-36
Figure 3.30 Setting Internal PSIP Data Insertion on the GUI .............................. 3-38
Fi
gure 3.31 Setting External PSIP Data Insertion on the GUI ............................. 3-40