evertz CP-2116E - Technical Description; Specifications; Control; Electrical

To Next Page

To Previous Page

CP-2116E

Remote Control Panel

Revision 1.2 Page - 9

3. TECHNICAL DESCRIPTION

3.1. SPECIFICATIONS

3.1.1. Control

Ethernet: 10/100 base T.RJ45 connector

Joystick: Parallel contact closure TTL levels, D9 male

3.1.2. Electrical

Voltage: Autoranging 100V - 240V AC, 50/60Hz

Power: 20 Watts

Fuse Rating: 250V, 4A, time delay

3.1.3. Physical

Full Width Panel: 19" W x 3.5" H x 1.2" D (483mm W x 89mm H x 32mm D)

Half Width Panel: 9.5" W x 3.5" H x 1.2" D (241mm W x 89mm H x 32mm D)

With Full Width 3RU Chassis for WFM Mounting:

19" W x 5.25" H x 1.2" D (483mm W x 133mm H x 32mm D)

Weight: 2lbs (.9kg)

Operating Temp: 0 - 40°C

3.1.4. Compliance

Safety: ETL Listed, complies with EU safety directives

EMI/RFI: Complies with FCC Part 15 Class A regulations

Complies with EU EMC directive

3.2. SERVICING INSTRUCTIONS

These servicing instructions are for use by qualified service personnel.

Main Page

Table of Contents7
Overview11
Figure 1-1: CP-2116E Control Panel11
Installation13
Rear Panel13
Figure 2-1: CP-2116E Rear Panel13
Front Control Panel14
Figure 2-2: CP-2116E Front Control Panel14
Power Connections15
Mounting15
Figure 2-3: One CP-2116E-H Mounted in a 3RU CPH-TEK with Owner Furnished Tektronix WFM15
Figure 2-5: One CP-2116E-H Mounted in a 2RU CPH-RMB with Supplied Blank Plate16
Figure 2-6: Two CP-2116E-H Mounted in a 2RU CPH-RMB16
Figure 2-7: Mounting Installation for the CP-2116-DBK16
Figure 2-8: Mounting Installation for the CP-2116-TEK17
Technical Description19
Specifications19
Control19
Electrical19
Physical19
Compliance19
Servicing Instructions19
Front Panel Control21
Front Panel Navigation Options21
Upgrading21
Configuring the Network Settings22
Testing the Panel's Functionality23
Key Test23
LCD Test23
Touchscreen Test23
GPIO Test23
Checking the Status of the Cp-2116E24
System Configuration25
Upgrading the Cp-2116E Panel25
Requirements25
Getting Started25
Upgrading Firmware on the CP-2116E26
Figure 5-1: Cp116E Web Interface26
Figure 5-2: Install Firmware Page26
Systems Menu27
Products Page27
Figure 5-3: Systems Drop down Menu27
Figure 5-4: Products Page27
Products Uploaded28
Service Templates Page28
Figure 5-5: Systems - Service Template Page28
Figure 5-6: Service Template List29
Table 5-1: Service Template Buttons29
Service Template Controls30
Figure 5-7: Customizing a Template30
Service Template Parameter Tree32
Figure 5-8: Parameter Tree32
Template Properties33
Creating a New Service Template33
Figure 5-9: New Template Page33
Service Template Controls34
Figure 5-10: Assigning a Parameter34
Services Page35
Figure 5-11: Services List35
Table 5-2: Service Template Buttons35
Service Controls36
Available Service Templates36
Service Properties36
Figure 5-12: Customizing a Service36
Add a Service Template to the Service List37
Systems Page37
Figure 5-13: Systems Page37
Table 5-3: Service Template Buttons37
Device Properties38
Figure 5-14: New System Window38
Discovery Menu39
Figure 5-15: Update System Window39
Figure 5-16: Discovery Menu39
Settings Page40
Figure 5-17: Settings Page40
Ranged Discovery Page41
Import Device Labels41
Figure 2-4: CP-2116E41
Figure 5-18: Ranged Discovery Page41
Figure 5-19: Import Device Labels Page41
Vistalink Alarm Server42
Figure 5-20: Vistalink Alarm Server42
Source Proc Menu43
Source Proc Page43
Figure 5-21: Source Proc Menu43
Figure 5-22: Source Proc Page43
Destination Proc Page44
Figure 5-23: Destination Proc Page44
Macros Page45
Figure 5-24: Macros Page45
Help Menu46
Help Page46
Panel Version46
Figure 5-25: Help Menu46
Figure 5-26: Help Page46
Product Support47
Figure 5-27: Product Support Tab47
Configuration48
Figure 5-28: Configuration Tab48
Figure 5-29: Opening Config.cf Dialog Box48
Logs Tab49
Figure 5-30: Logs Tab49
Figure 5-31: Opening Logs.lf Dialog Box49
Preferences Page50
Visual Settings50
Figure 5-32: Preferences Page50
Import/Export Page51
Figure 5-33: Import/Export Page51
Upgrade Menu52
Figure 5-34: Install Firmware Page52
Adding an Evertz System to Control53
Cp-2116E Control of Mvp System53
Figure 6-1: Systems Page53
Figure 6-2: Create a MVP System54
Adding Snmp Services55
Figure 6-3: Create a SNMP Service55
Adding an Eqx Server56
Figure 6-4: Add EQX Server56
Creating Source-Service Mapping57
Navigating the Control Panel59
Source (Src) Button59
Figure 7-1: Front Panel Display59
Figure 7-2: SRC Layout59
Figure 7-3: SRC Keypad Display60
Destination (Dst) Button61
Figure 7-4: DST Layout61
Figure 7-5: DST Keypad Display62
Up & down Arrows63
Clear Next Source Button63
Figure 7-6: up & down Arrows Display63
Figure 7-7: Clear Next Source Button63
Level Button64
Figure 7-8: Level Button Display64
Figure 7-9: Selecting the Video Button64
Figure 7-10: Select the ALL/NONE Button65
Figure 7-11: Selecting the BREAK AWAY Button65
Selecting the "More" Button66
Figure 7-12: Selecting the "MORE" Button66
Figure 7-13: Selecting the "CHNG PRFL" Button67
Figure 7-14: Selecting the "ENABLE TOGGLE" Button67
Figure 7-15: Selecting the "LOCK DST" Button68
Figure 7-16: Selecting the "PROTECT" Button69
Figure 7-17: Selecting the "TIELINES" Button69
Figure 7-18: Selecting the "ONE DST VIEW" Button70
Figure 7-19: Selecting the "TAKE" Button71
Figure 7-20: Selecting the "TOGGLE TAKE" Button71
Figure 7-21: Selecting the "SALVO" Button72
Figure 7-22: Selecting the "INFO" Button73
Figure 7-23: Selecting the "SRC INFO" Button73

evertz CP-2116E - Technical Description; Specifications; Control; Electrical

Table of Contents

Related product manuals