DTP CrossPoint 4K Series Matrix Switchers • Programming Guide 69
X1* = Video format 0 (input) = No signal detected
0 (output) = Auto (HDMI RGB Full to CEA sink or DVI to non-CEA sink)
1 = DVI (RGB 444, no audio, no InfoFrames)
2 = HDMI RGB Full (RGB 444, 000 - 255 audio, InfoFrames)
3 = HDMI RGB Limited (RGB 444, 016 - 255 audio, InfoFrames)
4 = HDMI YUV Full (RGB 444, 000 - 255 audio, InfoFrames)
5 = HDMI YUV Limited (RGB 444, 016 - 255 audio, InfoFrames)
6 = HDMI YUV Full (RGB 422, 000 - 255 audio, InfoFrames)
7 = HDMI YUV Limited (RGB 422, 016 - 255 audio, InfoFrames)
X1( = Output video bit depth 0 = Auto (default) 1 = 8-bit
X2) = Video mute status 0 = No mutes 2 = Video and sync
1 = Video mute
X2! = Input signal status 0 = No signal detected 1 = Sync detected
X2@ = TP and insertion input number
10x8 matrix 07, 08, 09, and 10
All others 07 and 08
X2# = Switch position 0 = DTP 1 = HDBT (output only) 2 = XTP
X2$ = Name 12 characters maximum
upper- and lower-case alphanumeric characters, as well as _, /, and spaces are valid.
NOTE: The HTML language reserves certain characters for specific functions (see Special Characters on page 84).
X2% = Scaler preset 001 – 128
X2^ = Logo number 00
–
16
(
00
= no logo)
X2& = Preset number 01 – 32
X2* = Lock mode 0 = Mode 0 1 = Mode 1 2 = Mode 2 (default)
X2( = Firmware version number to second decimal place (x.xx)
X3) = Verbose firmware version-description-upload date/time (see the Query firmware version (verbose) command on page 76).
X3! = Voltage Positive or negative voltage and magnitude
X3@ = Internal temperature Degrees Celsius
X3# = Picture adjustments 000 through 127 (064 = default)
X3$ = Position and size 10240 Horizontal position specified from left,
Vertical position specified from top
The default is the video resolution of the output.
X3% = Active pixels and active lines Dependent on the input signal and selected scaling.
X3^ = Aspect ratio fill or follow 1= fill (default) 2 = follow
X3& = Overscan percentage 0 = 0% (default) 1 =
2.5%
2 = 5.0%
X3* = Test pattern 00 = Disable (default)
01 = Crop 04 = Color bars
02 = Alternating pixels 05 = Grayscale
03 = Crosshatch 06 = Blue mode
X3( = Scaler preset available 0 = Unavailable 1 = Available
X4) = Screen save duration 0 = Output sync instantly disabled when no active video input is selected
001 through 500 (seconds)
501 = Output sync never times out (default)
X4! = Screen saver status 0 = Active input detected, timer is not running
1 = No active input, timer is running, output sync is still active
2 = No active input, timer is expired, output sync is disabled
X4@ = Scaler output resolution and rate See the table on page 80.
X4# = Captive screw or UART 0 = Captive screw RS-232 insert (default) 1 = Ethernet RS-232 insert (UART)
X4$
= Port number 02 — 0n = UARTs 2 — n (DTP input and output ports)
10x8 matrix 02 = Input 7 06 = Output 5
03 = Input 8 07 = Output 6
04 = Input 9 08 = Output 7
05 = input 10 09 = Output 8
8x6 matrix and 8x4 matrix 02 = Input 7 04 = Output 3
03 = Input 8 05 = Output 4
8x2 matrix 02 = Input 7 04 = Output 1
03 = Input 8 05 = Output 2
To Next Page
Loading...
