Fike FCP-300 - Page 7

FCP-300/FCP-300ECS Manual — P/N LS10145-002FK-E:A 3/12/2021 7
Table of Contents
8.1.2: Output Points ........................................................................................................................................................................................74
8.1.3: Running JumpStart Auto-Programming...............................................................................................................................................74
8.2: Mapping Overview ..........................................................................................................................................................................................75
8.2.1: Input Point Mapping .............................................................................................................................................................................75
8.2.2: Output Circuit Mapping........................................................................................................................................................................77
8.2.3: Event Mapping.....................................................................................................................................................................................77
8.2.4: Mapping LED Points ............................................................................................................................................................................81
8.2.5: Mapping LED Points for a Networked System ....................................................................................................................................82
8.3: Programming Using the HFSS Software Suite................................................................................................................................................82
8.4: Programming Using an Annunciator ...............................................................................................................................................................82
8.4.1: Entering / Exiting the Panel Programming...........................................................................................................................................82
8.4.2: Moving through the Menus ..................................................................................................................................................................83
8.4.3: Selecting Options and Entering Data....................................................................................................................................................83
8.5: Programming Menu Quick Reference .............................................................................................................................................................83
Section 9: Programming ................................................................................................................................................. 92
9.1: UL 864 / UL 2572 Programming Requirements..............................................................................................................................................92
9.2: Modules ...........................................................................................................................................................................................................92
9.2.1: Edit Modules.........................................................................................................................................................................................92
9.2.2: Adding a Module ..................................................................................................................................................................................93
9.2.3: Deleting a Module ................................................................................................................................................................................93
9.2.4: View Module List .................................................................................................................................................................................93
9.3: Zone .................................................................................................................................................................................................................93
9.3.1: Edit Zone ..............................................................................................................................................................................................94
9.3.2: View Zone Points .................................................................................................................................................................................96
9.4: Group ...............................................................................................................................................................................................................96
9.4.1: Edit Group ............................................................................................................................................................................................96
9.4.2: View Group Points ...............................................................................................................................................................................97
9.4.3: Edit OPG Template...............................................................................................................................................................................97
9.5: Point .................................................................................................................................................................................................................98
9.5.1: Point Programming For FIK-6815 Module ..........................................................................................................................................98
9.5.2: Point Programming for the Internal or the External Power Module (FIK-RPS1000)........................................................................100
9.5.3: Point Programming For FIK-5880 or 5865 Modules .........................................................................................................................101
9.5.4: Point Programming for FIK-5496 ..........................
............................................................................................................................102
9.5.5: Point Programming for FIK-AMP......................................................................................................................................................102
9.5.6: Point Programming for FIK-NVCM and FIK-RVM Modules...........................................................................................................103
9.6: System Options..............................................................................................................................................................................................105
9.6.1: Communication Options.....................................................................................................................................................................105
9.6.2: Daytime/Nighttime Sensitivity ...........................................................................................................................................................108
9.6.3: Holiday Days ......................................................................................................................................................................................108
9.6.4: Time Options ......................................................................................................................................................................................109
9.6.5: Miscellaneous Options........................................................................................................................................................................109
9.6.6: Daylight Saving Options.....................................................................................................................................................................110
9.6.7: Edit Banner .........................................................................................................................................................................................110
9.6.8: SLC Family.........................................................................................................................................................................................110
9.7: JumpStart® AutoProgramming ..................................................................................................................................................................... 111
9.8: Restore Defaults............................................................................................................................................................................................. 111
9.9: Voice Options................................................................................................................................................................................................. 111
9.9.1: FIK-NVCM Maintenance...................................................................................................................................................................111
9.9.2: Voice Settings.....................................................................................................................................................................................111
Section 10: System Operation...................................................................................................................................... 112
10.1: Default User and Installer Codes .................................................................................................................................................................112
10.2: Annunciator Description ..............................................................................................................................................................................112
10.2.1: LCD Display.....................................................................................................................................................................................112
10.2.2: Banner...............................................................................................................................................................................................112
10.2.3: Single Key Acknowledge .................................................................................................................................................................113
10.3: Menu System ...............................................................................................................................................................................................113
10.3.1: Main Menu Overview.......................................................................................................................................................................113
10.3.2: Using the Menus ...............................................................................................................................................................................113
10.4: Basic Operation ...........................................................................................................................................................................................113
10.4.1: Setting Time and Date ......................................................................................................................................................................113
10.4.2: Disable / Enable a Point....................................................................................................................................................................113