Fuji Electric FRENIC MEGA G2 Series - Page 731

11.2 Size of Current for Each Part of the Inverter
11-3
SELECTING PERIPHERAL EQUIPMENT
Chap 11
Table 11.2-1 Size of current for each part of inverter (cont.)
HHD specification: Heavy Duty applications
HND specification: Normal Duty applications
Power system
Specification
Standard applicable
motor (kW) [HP]
Inverter type
50 Hz, 400 V
60 Hz, 440 V
Braking
resistor
circuit
current (A)
Input RMS current (A)
DC intermediate
circuit current (A)
Input RMS current (A)
DC intermediate
circuit current (A)
DC reactor (DCR)
DC reactor (DCR)
Yes
N/A
Yes
N/A
Three-phase 400 V
HHD
0.4 [1/2]
FRN0002G2□-4G
0.85
1.7
1
0.74
1.7
0.99
0.8
HHD
0.75 [1]
FRN0003G2□-4G
1.6
3.1
2.0
1.5
2.9
1.9
1.1
HHD
1.5 [2]
FRN0004G2□-4G
3.0
5.9
3.7
2.8
5.4
3.5
1, 8
HHD
2.2 [3]
FRN0006G2□-4G
4.5
8.2
5.6
4.1
7.5
5.1
1, 8
HHD
3.7 [5]
FRN0009G2□-4G
7.5
13
9.2
6.9
11.8
8.5
2.1
HHD
5.5 [7.5]
FRN0018G2□-4G
10.6
17.3
13.0
9.6
15.7
11.8
3.2
HND
7.5 [10]
14.4
23.2
17.7
13.0
21.0
16.0
3.2
HHD
7.5 [10]
FRN0023G2□-4G
14.4
23.2
17.7
13.0
21.0
16.0
3.1
HND
11 [15]
21.1
33.0
25.9
19.0
29.8
23.3
3.1
HHD
11 [15]
FRN0031G2□-4G
21.1
33.0
25.9
19.0
29.8
23.3
4.5
HND
15 [20]
28.8
43.8
35.3
26.0
39.5
31.9
4.5
HHD
15 [20]
FRN0038G2□-4G
28.8
43.8
35.3
26.0
39.5
31.9
5.7
HND
18.5 [25]
35.5
52.3
43.5
32.0
47.1
39.2
5.7
HHD
18.5 [25]
FRN0045G2□-4G
35.5
52.3
43.5
32.0
47.1
39.2
7.2
HND
22 [30]
42.2
60.6
51.7
38.0
54.6
46.6
7.2
HHD
22 [30]
FRN0060G2□-4G
42.2
60.6
51.7
38.0
54.6
46.6
7.7
HND
30 [40]
57.0
77.9
69.9
51.4
70.2
63.0
7.7
HHD
30 [40]
FRN0075G2□-4G
57.0
77.9
69.9
51.4
70.2
63.0
10
HND
37 [50]
68.5
94.3
83.9
61.8
85.0
75.7
10
HHD
37 [50]
FRN0091G2□-4G
68.5
94.3
83.9
61.8
85.0
75.7
12
HND
45 [60]
83.2
114
102
75.0
103
91.9
12
HHD
45 [60]
FRN0112G2□-4G
83.2
114
102
75.0
103
91.9
15
HND
55 [75]
102
140
125
91.9
126
113
15
HHD
55 [75]
FRN0150G2□-4G
102
140
125
91.9
126
113
19
HND
75 [100]
138
-
169
124
-
152
19
HHD
75 [100]
FRN0180G2□-4G
138
169
124
152
24
HND
90 [125]
164
201
148
181
24
HHD
90 [125]
FRN0216G2□-4G
164
201
148
181
31
HND
110 [150]
201
246
181
222
31
HHD
110 [150]
FRN0260G2□-4G
201
246
181
222
35
HND
132 [200]
238
292
214
263
35
HHD
132 [200]
FRN0325G2□-4G
238
292
214
263
42
HND
160 [250]
286
350
258
315
42
HHD
160 [250]
FRN0377G2□-4G
286
350
258
315
50
HND
200 [300]
357
437
321
394
50
HHD
200 [300]
FRN0432G2□-4G
357
437
321
394
62
HND
220 [350]
390
478
351
430
62
(Note) □ in the inverter type is replaced by a letter of the alphabet.
□
S (basic type), E (type with built-in EMC filter)
• Inverter efficiency is calculated using values suitable for each inverter model. Furthermore, input RMS current
is calculated based on the following conditions.
[FRN0060G2□-4G or lower] Power supply capacity: 500 kVA, source impedance: 5%
[FRN0075G2□-4G or higher] Values commensurate with the capacity recommended by Fuji Electric are
used for calculating the power supply capacity and source impedance.
• The input RMS currents listed in the above table will vary in inverse proportion to the power supply voltage,
such as 380 V.
• The braking circuit current is always constant, independent of braking resistor type (built-in, standard,
10%ED).