Gorgy Timing LEDI - Page 79

MDE-LEDI-1099V4.0
79
ENGLISH
Subcategory
OID
G
E
T
S
E
T
Description
Model
.1.1.0
Y
N
Product name
serialNumber
.1.2.0
Y
N
Product serial number
versionNumber
.1.3.0
Y
N
Product version as x.x.x.x
Mac
.1.4.0
Y
N
Product MAC address
messageString
.1.5.0
Y
N
Synchronization message as presented on the homepage
("Synchronization Status:" field)
utcDateTime
.1.6.0
Y
Y
In recovery, returns the UTC time and date of the product.
In configuration:
- If the current mode is NTP, a "Read-Only" error is returned.
- - If the mode is Autonomous, then the UTC date is updated.
inputType
.1.7.0
Y
Y
Type of NTP mode or autonomous mode.
lastCompensate
.1.8.0
Y
N
Last correction made on the product time compared to the received
time
reset
.1.9.0
Y
Y
Product reset.
In reading mode, the information is always 0.
batteryState
.1.10.0
Y
N
Retrieves the battery status. Always returns 0, which is equivalent to
"battery high".
wifiPower
.1.11.0
Y
N
Retrieves the Wi-Fi power in dBm if the product is in Wi-Fi. If the
product is in Ethernet, a string like "No Wi-Fi configured" will be
returned.
functionMode
.2.1.0
Y
N
Recovers the current state of the clock display.
altDateTime
.2.2.0
Y
Y
Display time, in seconds, between the date and the time on the Hours-
Minutes-Seconds display
altTempText
.2.3.0
Y
Y
Display time, in seconds, between the temperature and the time on
the Hours-Minutes-Seconds display
tempValue
.2.4.0
Y
N
Temperature value read by the product, via the temperature sensor.
If the temperature option is not present, the returned value will be "--
.-"
useButtons
.2.5.0
Y
Y
Active/inactive status of buttons
If the buttons option is present, then this command can block or not
the use of the buttons to avoid unwanted manipulations.
ntpInputVersion
.3.1.0
Y
N
NTP Version
ntpInputMode
.3.2.0
Y
N
Current mode of the NTP connection:
- Client/server
- Broadcast
- - Other
ntpInputAuto
.3.3.0
Y
Y
Status of the automatic detection mode of NTP servers or the auto-
configuration mode
ntpInputOption
.3.4.0
N
N
No effect
ntpInputState
.3.5.0
Y
N
- Synchronization status of the current NTP client
- Best candidate for sharing time information
- Current server selected for synchronization by the NTP client
ntpInputActiveServ
erAddress
.3.6.0
Y
N
IPv4 address of the selected NTP server
ntpInputLastAccur
acy
.3.7.0
Y
N
Always 0
ntpInputRequestInt
erval
.3.8.0
Y
N
Always 0
ntpInputRequestN
umber
.3.9.0
Y
N
Number of requests sent for each 10ms interval
ntpServerNumber
.3.10.0
Y
N
Number of NTP servers that can be used
ntpServEntIndex
.3.11.1.1.
[0,1,2]
Y
N
Identifies each server with a particular index 0,1,2 or 3
ntpServEntAddres
s
.3.11.1.2.
[0,1,2]
Y
Y
IPv4 address of the server corresponding to the selected index
ntpServEntState
.3.11.1.3.
[0,1,2]
Y
Y
Status (enable/disable) of the server corresponding to the selected
index