Honeywell ACUIX - OSD Menu Tree; Table 3-2 Menu Tree - 18× Color (HDXA), 18× WDR;TDN (HDXJ), 26× WDR;TDN (HDXF)

ACUIX™ PTZ High Speed Analog Dome Installation and Configuration Guide
Document 800-05662V1 Rev A 15
04/11
OSD Menu Tree
Table 3-2 Menu Tree - 18× Color (HDXA), 18× WDR/TDN (HDXJ), 26× WDR/TDN (HDXF)
1. Language English (default), Français (French), Deutsch (German), Italiano (Italian), Español (Spanish), Polski (Polish), Nederlands (Dutch), Čeština (Czech)
2. Display Options 3. Control Options 4. Diagnostic Options 5. Camera Options 6. Function Programming 7. Enhanced Features
1. Camera Msg 1. PASS 1. Coordinates 1. Zoom and Focus
(1) Max Digital Zoom Mag
(2) Manual Zoom Speed
(3) Min Focus Length(cm)
1. PTZ Mimic Tour Menu
a
(1) Run a Mimic Tour
(2) Program a Mimic Tour
(3) Delete a Mimic Tour
1. Video Gain/PWM
Settings
(1) Video Gain (UTP)
(2) Lift PWM Level 0-100
(3) Gain PWM Level 0-100
(4) Char White Level 0-100
2. Sectors 2. Auto-Pivot 2. Total Run Time (PTZ,
IR&Fo)
2. Exposure Control
(1) NA
(2) Exposure Level
(3) NA
(4) NA
(5) NA
(6) NA
(7) Auto Slow Shutter
(8) Backlight Comp
2. Program a Preset
Tour
b
2. NA
3. Preset Names 3. Program Alarms
(1) Program Alarms
(2) Set Alarm Condition
(3) Enable Auto Ack
(4) Enter Alarm Message
(5) Alarm Overwrite
(6) Overwrite Time (sec)
3. Clear The Memory 3. NightShot Control
c
(1) NightShot Mode
(2) NightShot
(3) Activate
(4) Deactivate
3. Privacy Zone Options
(1) Change PrivZone
Priority
(2) Enable/Disable
PrivacyZone
(3) Privacy Zone Color
(4) Delete Privacy Zone
3. NA
4. Digital Zoom Mag 4. Set Pan and Tilt
Options
(1) Manual Speed deg/s
(2) Pan Reverse
(3) Tilt Reverse
(4) −5 deg Tilt Limit
(5) Find Home on Startup
(6) Pan Offset
(7) Startup State Restore
4. Operational
Diagnostics
(1) Display Error Logs
(2) Clear Error Logs
(3) Run Diagnostics ( Find
Home, Check Supply
Voltage)
4. White Balance
(1) High Light WB Mode
(2) Low Light WB Mode
(3) Enter High Lght 28dB
(4) Enter Low Lght 28dB
(5) Manual White Balance
(6) Red Gain
(7) Blue Gain
4. List PS/PT/Sectors
(1) Presets
(2) Preset Tours
(3) Sectors
4. NA
5. Start-up Screen Msg 5. Set Default Function 5. NA 5. Video Options
c
(1) Still Preset
(2) E-Flip
(3) Mirror Image
5. Program Sector
b
5. Time & Date Settings
(1) Display Time
(2) Display Date
(3) Time Format
(4) Change Time
(5) Change Date
6. Change Camera Name
Loc.
6. Auto Focus 6. Restore Default
Settings
6. Vert Phase Edge 6.
Program Privacy Zone
b
6. Display Supply
Voltages
7. Change Sector Name
Loc.
7. Preset Tour Auto Foc 7. Scan and Camera
Reset
7. Vert Phase 0–359.9 7. Delete PS/PT/MT/
Sectors
b
7. Timed Functions
8. Crosshairs 8. Preset Auto Focus 8. NA
9. Dome Name Settings
(1) Set Dome Name
(2) Display Dome Name
(3) Change Dome Name
Location
9. Timed Auto Focus (sec) 9. WDR & Motion
Detection
c
(1) Wide Dynamic Range
(2) Motion Detection
a
Diamond/IntelliBus™ protocol only
b
MAXPRO-mode/VCL/VCL UTC/Pelco P/Pelco D/AD/Pelco P_AD/Pelco D_AD protocol only
c
Not available with 18× Color (HDXA) cameras