Icom IC-7851 - Page 219

15-8
15
SET MODE
USB IF Output Level (Default: 50%)
Sets the [USB B] output level.
• Range: 0%–100% (in 1% steps)
LAN Output Select (Default: AF)
Selects the signal output from [LAN].
• AF: AF signal is output from [LAN].
• IF: IF signal is output from [LAN].
LAN AF SQL (Default: OFF(OPEN))
Select the squelch behavior of [LAN].
• OFF(OPEN): The squelch is always opened regard-
less of the transceiver's squelch con-
dition.
• ON: The squelch opens and closes, ac-
cording to the transceiver's squelch
condition.
ACC-A MOD Level (Default: 50%)
Sets the modulation input level of [A ACC1].
• Range: 0%–100% (in 1% steps)
• Approximately 200 mV at the 50% (default) setting.
ACC-B MOD Level (Default: 50%)
Sets the modulation input level of [B ACC1].
• Range: 0%–100% (in 1% steps)
• Approximately 200 mV at the 50% (default) setting.
S/PDIF MOD Level (Default: 50%)
Sets the modulation input level of [S/P DIF].
• Range: 0%–100% (in 1% steps)
USB MOD Level (Default: 50%)
Sets the modulation input level of [USB].
• Range: 0%–100% (in 1% steps)
LAN MOD Level (Default: 50%)
Sets the modulation input level of [LAN].
• Range: 0%–100% (in 1% steps)
DATA OFF MOD (Default: MIC,ACC-A,ACC-B)
Selects the connector(s) to input the modulation signal
when the data mode is OFF.
• MIC: Use the signal from [MIC].
• ACC-A: Use the signal from [A ACC1]
(pin 4).
• ACC-B: Use the signal from [B ACC1]
(pin 4).
• MIC,ACC-A: Use the signal from [MIC] and
[A ACC1] (pin 4).
• MIC,ACC-B: Use the signal from [MIC] and
[B ACC1] (pin 4).
• ACC-A,ACC–B: Use the signal from [A ACC1]
and [B ACC1] (pin 4).
• MIC,ACC-A,ACC–B: Use the signal from [MIC], [A
ACC1] and [B ACC1] (pin 4).
• USB: Use the signal from [USB].
• S/P DIF: Use the signal from [S/P DIF].
• LAN: Use the signal from [LAN].
DATA1 MOD (Default: ACC-A)
Selects the connector(s) to input the modulation signal
when the data 1 mode (D1) is ON.
• MIC: Use the signal from [MIC].
• ACC-A: Use the signal from [A ACC1]
(pin 4).
• ACC-B: Use the signal from [B ACC1]
(pin 4).
• MIC,ACC-A: Use the signal from [MIC] and
[A ACC1] (pin 4).
• MIC,ACC-B: Use the signal from [MIC] and
[B ACC1] (pin 4).
• ACC-A,ACC–B: Use the signal from [A ACC1]
and [B ACC1] (pin 4).
• MIC,ACC-A,ACC–B: Use the signal from [MIC], [A
ACC1] and [B ACC1] (pin 4).
• USB: Use the signal from [USB].
• S/P DIF: Use the signal from [S/P DIF].
• LAN: Use the signal from [LAN].
DATA2 MOD (Default: ACC-B)
Selects the connector(s) to input the modulation signal
when data 2 mode (D2) is ON.
• MIC: Use the signal from [MIC].
• ACC-A: Use the signal from [A ACC1]
(pin 4).
• ACC-B: Use the signal from [B ACC1]
(pin 4).
• MIC,ACC-A: Use the signal from [MIC] and
[A ACC1] (pin 4).
 ACC set screen (continued)