I-1
INDEX
Symbol
∂F scan ................................................................12-9
∂TX function ...........................................................8-5
Monitor function .................................................8-5
Number
1⁄4 tuning step function ...........................................4-9
1.2 kHz Filter calibration .........................................7-8
137 kHz band operation .........................................5-8
5 MHz frequency band operation .........................4-18
A
ABOUT THE SUPPLIED CD .....................................iv
About the VOX function ..........................................8-2
ACC set screen .............................................2-8, 15-6
ACC socket ...........................................................20-2
ACC1 ...............................................................20-2
ACC2 ...............................................................20-2
Advanced connections ...........................................3-5
AFC/NET function .................................................5-28
AGC
AGC function control .........................................7-4
AGC time constant ............................................7-4
Setting the AGC time constant preset value ......7-4
AM mode
Operating AM or FM ........................................5-36
Antenna connection and selection ........................13-2
Antenna Memory ..................................................10-4
Antenna memory settings .....................................13-3
Antenna selection mode .......................................13-5
Antenna tuner ..............................................13-7, 19-3
Using the Antenna tuner operation ..................13-7
If the tuner cannot tune the antenna ...............13-8
Antenna type ...............................................2-16, 13-4
Selecting the antenna type ..............................13-4
APF (Audio Peak Filter) operation ..........................5-6
Attenuator ...............................................................7-2
Audio scope screen ..............................................6-15
AUDIO SCOPE SET ..........................................2-6
Audio scope set mode .....................................6-16
FFT Scope
FFT Scope Waterfall Display ......................6-16
FFT Scope Waveform Color .......................6-16
FFT Scope Waveform Type ........................6-16
Oscilloscope
Oscilloscope Waveform Color .....................6-16
Audio level ..............................................................4-4
Automatic transmission/reception setting ....5-18, 5-30
Auto notch function ...............................................7-13
Auto tuning step function ........................................4-8
Averaging ..............................................................6-10
B
Band edge warning beep......................................4-15
Entering the user band edge ...........................4-16
Register the Band edge ...................................4-16
User band edge ...............................................4-15
Band stacking registers ..........................................4-6
Band selection
Selecting the Main and Sub bands ....................4-5
BPSK and QPSK modes ......................................5-27
BPSK31 and BPSK63 modes ...............................5-27
Break-in function .....................................................8-4
Full break-in operation .......................................8-4
Semi break-in operation ....................................8-4
C
Calibration the Frequency (approximate) .............16-4
Capture list screen ..............................................10-10
Checking the firmware version .............................17-2
Checking the repeater input signal .......................5-37
CI-V
CI-V Address ...................................................10-4
CI-V connection ...............................................18-2
Command table ...............................................18-3
Data content description ................................18-10
Data format ......................................................18-2
Preparing .........................................................18-2
Cleaning ...............................................................16-7
Clock
Entering the CLOCK2 Name ...........................14-3
Selecting the CLOCK2 Function .....................14-3
Setting the CLOCK2 UTC Offset .....................14-3
Setting the Current time ..................................14-2
Setting the Date ...............................................14-2
Clock backup battery replacement .......................16-9
Confirming programmed memory channels .........11-3
Connecting a non-Icom linear amplifier ..................3-7
Connecting antenna ...............................................3-3
Connecting the IC-PW1/EURO ..............................3-7
Connections
Advanced connections ......................................3-5
Required connections ........................................3-4
Connector
Microphone connector .....................................20-3
[REF I/O] connector .........................................20-4
[RX-I/O] connector ...........................................20-5
[X-VERTER] connector ....................................20-4
Contest number set mode ....................................5-12
Convenient functions for Receive ...........................5-2
Convenient functions for Transmit ...........................5-3
To Next Page
Loading...
