EasyManuals Logo

Juniper SRX100 Hardware Guide

Juniper SRX100
154 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #74 background imageLoading...
Page #74 background image
Table 19: Services Gateway Prerequisite Tasks
DetailsTask
Device identification
Hostname for the device on the network
Domain that the device belongs to on the network
Password for the root user
Time zone information
System time and zone for services gateway location
IP address of a Network Time Protocol (NTP) server,
if NTP is used to set the time on the services
gateway
Network settings for the services gateway:
IP address of a DNS server
List of domains that can be appended to hostnames
for DNS resolution
IP address of the default gateway
IP address to be used for the loopback interface
IP address of the built-in Ethernet port that you will use
for management purposes. For example, use the fe-0/0/0
interface
Gather the information on:
Management device, such as a laptop, with an Ethernet
port
Ethernet cable (provided)
If you are performing the initial configuration with the J-Web
interface, gather the following equipment:
Management device, such as a PC or laptop, with a serial
port and an asynchronous terminal application (such as
Microsoft Windows HyperTerminal)
Ethernet cable (provided)
For a remote connection, gather the following equipment:
Two dial-up modems
An adapter appropriate for your modem (not
provided)
If you are performing the initial configuration with the CLI,
gather the following equipment:
Related Topics SRX100 Services Gateway Autoinstallation Overview on page 53
SRX100 Services Gateway Basic Connectivity Settings on page 56
Built-In Ethernet Ports for the SRX100 Services Gateway on page 58
Management Access for the SRX100 Services Gateway on page 59
Connecting an SRX100 Services Gateway to the J-Web Interface on page 60
Connecting an SRX100 Services Gateway to the CLI Locally on page 62
Connecting an SRX100 Services Gateway to the CLI Remotely on page 64
SRX100 Services Gateway Basic Connectivity Settings
Table 20 on page 57 provides information on basic connectivity settings.
56 SRX100 Services Gateway Basic Connectivity Settings
SRX100 Services Gateway Hardware Guide

Table of Contents

Other manuals for Juniper SRX100

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Juniper SRX100 and is the answer not in the manual?

Juniper SRX100 Specifications

General IconGeneral
Routing protocolsBGP, IS-IS, MPLS, OSPF
Switching protocolsVLAN 802.1Q, 802.3ad/LACP, STP
Supported network protocolsIPv4, IPv6, CLNS
Firewall securityYes
Security algorithms3DES, DES
Authentication methodRADIUS, RSA SecureID, LDAP
VPN supportIPsec VPN
Data transfer rate0.1 Gbit/s
Input voltage100 - 240 V
Input frequency50/60 Hz
Heat dissipation35 BTU/h
Power requirements100-240, 50/60
Power over Ethernet (PoE)No
Power consumption (typical)30 W
SafetyUL 60950-1, CSA 60950-1, AS / NZS 60950-1, AS / NZS 60950-1, CB Scheme, EN 60950-1
CertificationFCC Class B ICES class B AS / NZS CISPR22 Class B AS / NZS CISPR22 Class B VCCI Class B EN 55022 Class B, EN 300386
Mounting typeRack mounting
Internal memory1024 MB
Storage temperature (T-T)-20 - 70 °C
Operating temperature (T-T)0 - 40 °C
Weight and Dimensions IconWeight and Dimensions
Weight1100 g
Dimensions (WxDxH)216 x 147 x 36 mm

Related product manuals